- ページ 2

ゲートオープナー DoorKing 9100のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。DoorKing 9100 2 ページ。

QUICKSTART "BASIC" GUIDELINES FOR MODEL 9100 - DIP-SWITCH AND WIRING REFERENCE

Model 9100 is intended for installation only on sliding gates used for vehicles.

Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to the Installation/Owner's manual.

Switch

Function

Setting

SW 1

Changes the direction the operator will open/close the gate depending on the different chain configurations.

Front

Opening

Mount

direction

using ON

using OFF

setting.

OFF

Auto-Close

Timer

OFF

Motor

Hold

4-OFF

5-OFF

Relay Activation

and

4-OFF

5-ON

4 and 5

LED Indicator

4-ON

5-OFF

Light Activation

4-ON

5-ON

SW 1

OFF

Self-Test

7-OFF

8-OFF

Gate Open

7-OFF

8-ON

7 and 8

Back-Off

7-ON

8-OFF

Position

7-ON

8-ON

Note: After a DIP-switch setting is changed, power must be turned OFF and then turned back on for the new setting to take affect.

SW 2

Switch

Function

Setting

Exit Loop Port

OFF

Jumper Wire

Needed

Output

See Manual

Full Open Input

OFF

Reverses Gate

Stops Gate

OFF

Partial Open

(14 Ft)

OFF

Built-in

Solenoid

Lock

OFF

Operator Model

Select

OFF

SW 2

Quick-Close

Timer Override

7-OFF

8-OFF

Gate Close

7-OFF

8-ON

7 and 8

Back-Off

7-ON

8-OFF

Position

7-ON

8-ON

Description

Center or

All Rear

Opening

Opens

direction

Post

direction

Mounts

with

Mounts

Left

using OFF

using ON

setting.

OFF

setting.

Auto-close timer is OFF. Manual input required to close gate.

Auto-close timer is ON. Adjustable from 1-23 seconds to close gate.

Normal Setting. No voltage to motor when gate is stopped (Level gate).

Voltage applied to motor always. Keeps inclined gate from coasting when stopped.

Relay activates and LED is ON when the gate is fully open.

Relay activates and LED is ON when the gate is not closed.

Relay activates and LED is ON when the gate is opening and open.

Relay activates and LED is ON when the gate is opening and closing.

Normal Setting.

Runs self-test. Caution: Bench testing ONLY!

Normal Setting. Gate fully opens.

Gate stops short 1" from full open position. Used for a reversing edge device.

Gate stops short 2" from full open position. Used for a reversing edge device.

Gate stops short 3" from full open position. Used for a reversing edge device.

Description

A plug-in exit loop detector plugged into the EXIT Loop port will partially open single

operator or fully open dual operators depending on type of loop detector used).

Normal Setting. Plug-in exit loop detector will fully open gate (Single operator).

Normal Setting. Input to terminal #6 and/or reverse loops will reverse gate

during close cycle.

Input to terminal #6 and/or reverse loops will stop gate during close cycle – gate

will continue to close after input to terminal #6 and/or reverse loops are cleared

(Helps prevent tailgating vehicles from unauthorized entry).

Normal Setting. Switch must be OFF for terminal #5 input to open gate 14 Ft.

DO NOT use ON setting. NOT associated with partial open feature for the 9100.

Normal Setting. Fail-safe logic. Lock engages only if attempt is made to force gate

open (Factory setup).

Fail-secure logic. Lock engages after each gate cycle (2600-862 Lock kit required).

Normal Setting. Switch must be OFF for Model 9100.

DO NOT use ON setting for Model 9100.

Normal Setting. Timer will function normally.

Opening gate will stop and begin to close as soon as all reversing inputs (Reverse

loops, photo sensors) are cleared regardless of the distance the gate has opened.

Normal Setting. Gate fully closes.

Gate stops short 1" from full close position. Used for a reversing edge device.

Gate stops short 2" from full close position. Used for a reversing edge device.

Gate stops short 3" from full close position. Used for a reversing edge device.

Important:

Controls intended for user activation must be located at least six (6) feet away from any

moving part of the gate and where the user is prevented from reaching over, under, around or

through the gate to operate the controls. Emergency access controls only accessible by authorized

personnel (e.g., fire, police, EMS) may be placed at any location in the line-of-sight of the gate.

3-Wire Radio

#5 Terminal Note (Single

Operator Only): Any opening

All Rear

device connected to terminal #5 will

Opens

open the gate to the partial open

SW 2,

Mounts

with

Right

14-ft setting. External entrapment

switch 3

protection devices will also open the

must be

gate to the partial open setting. If the

OFF.

Inherent Reverse Sensor gets

setting.

activated during the close cycle, it

SW 2

will always fully open the gate.

Entrapment Protection must be provided

for the gate system where the risk of

entrapment or obstruction exists.

The operator will NOT run without one or

more monitored type B1 or B2 external

entrapment protection devices in EACH

direction of gate travel (minimum of 2

external devices required). See manual

for more information.

#4-Connected device fully opens gate.

#5-Connected device opens gate 14-feet.

3-Button Control

Station Jumper

Telephone

Entry

External Entrapment

Protection Devices

Key Switch

Stand-Alone

Keypad

Connect ONLY MONITORED

Stand-Alone

Card Reader

Note:

All stand-alone

and telephone

IMPORTANT:

entry devices

Edge sensors must be end-of-line

must use a

resistive types. See specific

separate power

manufacturer's wiring manual for

source.

more information.

UL 325 August

2018 Standard

Relay -

#2 - Full Open.

#5 - Opens gate 14-feet.

Com

24 volt

Receiver

250 mamp.

max.

W A

R N

SER

VIN

Oper

IOU

S INJ

and

ate

gate

CAN

free

only

peop

when

Y OR

CAU

not

oper

allow

and

gate

DEA

not

ate

child

gate.

ren

obstr

uctio

area

CON

path

while

stand

play

ns.

sight

FOR

Read

owne

gate

path

gate

area

manu

r's

movi

ng.

walk

CAN

CER

ANS

and

throu

/CSA

TIFI

safet

y instr

VEH

ICU

C22

uctio

CLA

LAR

NO.

247

53382

ns.

MOD

GAT

E OPE

RAT

SER

IAL

VOL

ERS

AMP

REV

LOO

MAX

PHA

GAT

E LOA

Door

King

, Inc.,

Ingle

woo

LOO

EXIT

OPE

TIM

TCH

KEY

SWI

RKI

DOO

2-0

460

ERS

REV

SIT

IVIT

SEN

Stop

4-Wire 3-Button

Control Station

Full Open

E N

O P

Jumper Pins 1 & 2 ONLY when

S E

C L O

using a 4-wire control station

Com

to enable stop terminal #7.

O P

S T

IMPORTANT:

Only 1 monitored Device can be connected

to each input. An OPTIONAL Expansion Kit (sold

separately) will allow connection for additional devices.

Close Beam

Wall

Open Edge

Filler Post If necessary

Closed Gate

Open Beam

UL 325 Terminal

1 - OPEN Beam STOP

2 - Ground (Common)

3 - CLOSE Beam REVERSE

4 - Ground (Common)

5 - 24 VAC 250 ma. Max

6 - Ground (Common)

7 - OPEN Edge/Beam REVERSE

Devices

8 - Ground (Common)

9 - CLOSE Edge/Beam REVERSE

10 - Ground (Common)

UL 325 DIP-Switches

DIP-switches MUST be turned ON for each device wired to terminal.

1 - OPEN Beam (UL 325 Terminal 1)

Monitored Photo and

2 - CLOSE Beam (UL 325 Terminal 3)

3 - OPEN Edge (UL 325 Terminal 7)

4 - CLOSE Edge (UL 325 Terminal 9)

120 S. Glasgow Avenue

Inglewood, California 90301

U.S.A.

24 Volt - 250 mamp. max.

Relay N.O. - #2 - Full Open.

#5 - Opens gate 14-feet.

4-Wire

Relay Com

Receiver

24 Volt Com

Terminal #3 Note:

Exceeding 250 mA of power from this terminal may cause the circuit

board transformer to overheat, causing intermittent problems.

Common

Full Open

EXIT

LOOP

24 V Power

FULL

FULL OPEN

ULL

Full Open

OPEN

TIMER

Partial Open

ENABLE STOP

SHORT PINS 1&2

S 1&2 &2

3-Button Control

Station Jumper

SW3

DOORKING

UL 325

4602-018

DIP-Switches

UL 325

Terminal

SW1

SW2

Common

2-Pin Supplied

Wire Harness

Fire Dept

Open

Gate will ONLY OPEN when this device is activated by authorized

personnel ONLY (fire, police, EMS) and operator has power.

Alarm will sound during entire open cycle. Operator will then go

into a hard shutdown once fully opened. Operator MUST be reset

to function normally again. This device MUST be mounted in the

line-of-site of gate so authorized personnel can monitor gate

movement.

Dual Gate Operators Note: Connect device to BOTH operators,

both gates will fully open.

Activation Note: Activation of this device will OPEN gate

regardless of the status of the open direction monitored external

entrapment protection device(s). If gate is opening, and the

operator's inherent entrapment protection system detects an

obstruction, the operator will reverse approx. 2 inches and go

into a hard shutdown. Operator reset button MUST be pushed to

function again OR cycle operator's power.

Com