DoorKing 9100 빠른 시작 매뉴얼 - 페이지 2
{카테고리_이름} DoorKing 9100에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DoorKing 9100 2 페이지.
페이지 인쇄
QUICKSTART "BASIC" GUIDELINES FOR MODEL 9100 - DIP-SWITCH AND WIRING REFERENCE
Model 9100 is intended for installation only on sliding gates used for vehicles.
Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to the Installation/Owner's manual.
Switch
Function
Setting
SW 1
Changes the direction the operator will open/close the gate depending on the different chain configurations.
Front
1
Opening
Opening
Mount
direction
direction
using ON
using OFF
setting.
setting.
OFF
Auto-Close
2
Timer
ON
OFF
Motor
3
Hold
ON
4-OFF
5-OFF
Relay Activation
and
4-OFF
5-ON
4 and 5
LED Indicator
4-ON
5-OFF
Light Activation
4-ON
5-ON
SW 1
OFF
6
Self-Test
ON
7-OFF
8-OFF
Gate Open
7-OFF
8-ON
7 and 8
Back-Off
7-ON
8-OFF
Position
7-ON
8-ON
Note: After a DIP-switch setting is changed, power must be turned OFF and then turned back on for the new setting to take affect.
SW 2
Switch
Function
Setting
Exit Loop Port
OFF
Jumper Wire
Needed
1
Output
See Manual
ON
Full Open Input
OFF
Reverses Gate
2
ON
Stops Gate
OFF
Partial Open
3
(14 Ft)
ON
OFF
Built-in
4
Solenoid
Lock
ON
OFF
Operator Model
5
Select
ON
OFF
SW 2
Quick-Close
6
ON
Timer Override
7-OFF
8-OFF
Gate Close
7-OFF
8-ON
7 and 8
Back-Off
7-ON
8-OFF
Position
7-ON
8-ON
Description
Center or
All Rear
Opening
Opening
Opens
direction
Post
direction
Mounts
with
Mounts
Left
using OFF
using ON
setting.
setting.
OFF
setting.
Auto-close timer is OFF. Manual input required to close gate.
Auto-close timer is ON. Adjustable from 1-23 seconds to close gate.
Normal Setting. No voltage to motor when gate is stopped (Level gate).
Voltage applied to motor always. Keeps inclined gate from coasting when stopped.
Relay activates and LED is ON when the gate is fully open.
Relay activates and LED is ON when the gate is not closed.
Relay activates and LED is ON when the gate is opening and open.
Relay activates and LED is ON when the gate is opening and closing.
Normal Setting.
Runs self-test. Caution: Bench testing ONLY!
Normal Setting. Gate fully opens.
Gate stops short 1" from full open position. Used for a reversing edge device.
Gate stops short 2" from full open position. Used for a reversing edge device.
Gate stops short 3" from full open position. Used for a reversing edge device.
Description
A plug-in exit loop detector plugged into the EXIT Loop port will partially open single
operator or fully open dual operators depending on type of loop detector used).
Normal Setting. Plug-in exit loop detector will fully open gate (Single operator).
Normal Setting. Input to terminal #6 and/or reverse loops will reverse gate
during close cycle.
Input to terminal #6 and/or reverse loops will stop gate during close cycle – gate
will continue to close after input to terminal #6 and/or reverse loops are cleared
(Helps prevent tailgating vehicles from unauthorized entry).
Normal Setting. Switch must be OFF for terminal #5 input to open gate 14 Ft.
DO NOT use ON setting. NOT associated with partial open feature for the 9100.
Normal Setting. Fail-safe logic. Lock engages only if attempt is made to force gate
open (Factory setup).
Fail-secure logic. Lock engages after each gate cycle (2600-862 Lock kit required).
Normal Setting. Switch must be OFF for Model 9100.
DO NOT use ON setting for Model 9100.
Normal Setting. Timer will function normally.
Opening gate will stop and begin to close as soon as all reversing inputs (Reverse
loops, photo sensors) are cleared regardless of the distance the gate has opened.
Normal Setting. Gate fully closes.
Gate stops short 1" from full close position. Used for a reversing edge device.
Gate stops short 2" from full close position. Used for a reversing edge device.
Gate stops short 3" from full close position. Used for a reversing edge device.
Important:
Controls intended for user activation must be located at least six (6) feet away from any
moving part of the gate and where the user is prevented from reaching over, under, around or
through the gate to operate the controls. Emergency access controls only accessible by authorized
personnel (e.g., fire, police, EMS) may be placed at any location in the line-of-sight of the gate.
3-Wire Radio
#5 Terminal Note (Single
Operator Only): Any opening
All Rear
device connected to terminal #5 will
Opens
open the gate to the partial open
SW 2,
Mounts
with
Right
14-ft setting. External entrapment
switch 3
protection devices will also open the
must be
gate to the partial open setting. If the
OFF.
ON
Inherent Reverse Sensor gets
setting.
activated during the close cycle, it
SW 2
will always fully open the gate.
Entrapment Protection must be provided
for the gate system where the risk of
entrapment or obstruction exists.
The operator will NOT run without one or
more monitored type B1 or B2 external
entrapment protection devices in EACH
direction of gate travel (minimum of 2
external devices required). See manual
for more information.
#4-Connected device fully opens gate.
#5-Connected device opens gate 14-feet.
3-Button Control
Station Jumper
Telephone
Entry
External Entrapment
Protection Devices
Key Switch
Stand-Alone
Keypad
Connect ONLY MONITORED
Stand-Alone
Card Reader
Note:
All stand-alone
and telephone
IMPORTANT:
entry devices
Edge sensors must be end-of-line
must use a
resistive types. See specific
separate power
manufacturer's wiring manual for
source.
more information.
UL 325 August
2018 Standard
Relay -
#2 - Full Open.
#5 - Opens gate 14-feet.
Com
24 volt
Receiver
250 mamp.
max.
W A
R N
IN
G
MO
SER
VIN
G
Oper
IOU
S INJ
GA
TE
and
ate
gate
UR
CAN
free
Do
of
only
peop
when
Y OR
CAU
SE
not
oper
or
allow
le
and
gate
DEA
TH
not
Do
ate
child
gate.
ren
obstr
uctio
area
is
in
CON
path
while
stand
to
play
in
ns.
sight
FOR
MS
Read
owne
gate
in
is
gate
path
gate
area
TO
manu
r's
movi
ng.
walk
or
CAN
CER
ANS
I/
al
and
throu
gh
/CSA
TIFI
safet
y instr
VEH
ICU
C22
.2
ED
TO
uctio
CLA
LAR
NO.
247
53382
ns.
MOD
SS
GAT
E OPE
EL
RAT
SER
IAL
HP
OR
VOL
E
TS
ERS
AMP
S
REV
LOO
P
MAX
PHA
GAT
E LOA
SE
Door
King
D
60
Hz
, Inc.,
Ingle
woo
d,
CA
N
LOO
EXIT
P
OPE
TIM
ER
TCH
KEY
SWI
RKI
NG
DOO
2-0
10
460
1
2
ERS
E
Y
3
4
REV
SIT
IVIT
5
2
SEN
SW
1
SW
NC
NO
Stop
4-Wire 3-Button
Control Station
Full Open
E N
O P
1
Jumper Pins 1 & 2 ONLY when
Close
S E
2
C L O
using a 4-wire control station
Com
3
to enable stop terminal #7.
O P
S T
IMPORTANT:
Only 1 monitored Device can be connected
to each input. An OPTIONAL Expansion Kit (sold
separately) will allow connection for additional devices.
Close Beam
Wall
Open Edge
Filler Post If necessary
Closed Gate
Open Beam
UL 325 Terminal
1 - OPEN Beam STOP
2 - Ground (Common)
3 - CLOSE Beam REVERSE
4 - Ground (Common)
5 - 24 VAC 250 ma. Max
6 - Ground (Common)
7 - OPEN Edge/Beam REVERSE
Devices
8 - Ground (Common)
9 - CLOSE Edge/Beam REVERSE
10 - Ground (Common)
UL 325 DIP-Switches
DIP-switches MUST be turned ON for each device wired to terminal.
1 - OPEN Beam (UL 325 Terminal 1)
Monitored Photo and
2 - CLOSE Beam (UL 325 Terminal 3)
3 - OPEN Edge (UL 325 Terminal 7)
4 - CLOSE Edge (UL 325 Terminal 9)
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
24 Volt - 250 mamp. max.
Relay N.O. - #2 - Full Open.
#5 - Opens gate 14-feet.
4-Wire
Relay Com
Receiver
24 Volt Com
Terminal #3 Note:
Exceeding 250 mA of power from this terminal may cause the circuit
board transformer to overheat, causing intermittent problems.
1
Common
2
Full Open
EXIT
LOOP
3
24 V Power
FULL
FULL OPEN
ULL
4
Full Open
OPEN
TIMER
5
Partial Open
6
ENABLE STOP
1
SHORT PINS 1&2
S 1&2 &2
3-Button Control
2
7
Station Jumper
3
8
SW3
DOORKING
UL 325
9
4602-018
DIP-Switches
10
1
2
11
3
4
12
5
6
13
13
7
UL 325
14
14
8
Terminal
9
15
10
16
SW1
SW2
NC
17
NO
18
Common
2-Pin Supplied
Wire Harness
Fire Dept
Open
Gate will ONLY OPEN when this device is activated by authorized
personnel ONLY (fire, police, EMS) and operator has power.
Alarm will sound during entire open cycle. Operator will then go
into a hard shutdown once fully opened. Operator MUST be reset
to function normally again. This device MUST be mounted in the
line-of-site of gate so authorized personnel can monitor gate
movement.
Dual Gate Operators Note: Connect device to BOTH operators,
both gates will fully open.
Activation Note: Activation of this device will OPEN gate
regardless of the status of the open direction monitored external
entrapment protection device(s). If gate is opening, and the
operator's inherent entrapment protection system detects an
obstruction, the operator will reverse approx. 2 inches and go
into a hard shutdown. Operator reset button MUST be pushed to
function again OR cycle operator's power.
Com