- ページ 11

スポットライト Dot-Spot clarios eco 10 WのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Dot-Spot clarios eco 10 W 15 ページ。

ページを印刷する

Configurations

Electrical connection

Order

clarios eco 6 Watt

number

5 m PUR-

cable, with

.33



open cable

end

0,3 m with

.41



M12 plug

5 m PUR-

cable with

.42



M12 plug

Optional accessories

Order number

ground spike ES 20

93000

marten repellent MS

93001

installation extension

93201

dazzle protection BS

93104

eco

Safety

Intended use

The garden and object spots clarios eco are designed for providing effect lighting for plants and

objects as well as for permanent installation. They are designed for operating in moderate climatic

zones and under water (depth 1 m). The luminary is meant for operating with protective low voltage.

In case of detailed lighting planning, please request the light distribution curves (LDC).

Installation to be carried by an expert

The installation may only be carried out by appropriately trained professionals.

Safety instructions

During installation, the relative safety regulations have to be followed. The spot is operated with

protective low voltage of 24 DC. To avoid danger and failures, prior or any work at the spot or instal-

lation, disconnect the power supply from the mains. The spot can't be opened. Connect the sport

only to power supplies with a maximum output voltage of 24 V DC. A wrong voltage may destroy the

spot and the power supply.

clarios eco 10 Watt

Dimmable



length 50 cm

length 10 cm, for raised assembly

stainless steel, put on from outside

Safety

Safety instructions

Observe the installation manual of the power supply. Do not overload the power supply! The overall

power consumed by all consumers connected to the power supply should be approx. 10% lower

than the rated power of the power supply being used.

In order to protect the exposed connection cable from rodents it should be protected against mar-

tens (see installation accessories).

High ambient temperatures shorten the life of the LED's. Ensure a good heat dissipation in order to

guarantee a long life of the LED. During operation, do not expose the spot to ambient temperatures

of > 45°C. Do not cover the spot, provide free air circulation.

Do not open the housing of the luminary. The tightness of the clarios eco is only guaranteed if also

the outer sheath of the connection cable is undamaged and if the connection cable is bonded in a

waterproof way. Otherwise, because of the capillary effect, the penetrating moisture can reach and

destroy the electronics of the spot.

Assembly

Preparation

Depending on the configuration, unpack all the parts included in the scope of delivery and check

them for completeness and intactness.

Dispose of the packaging material no longer needed in accordance with applicable regulations.

If you notice any damage from transport, immediately contact the dealer where you purchased the

luminary.

Mechanical installation

Mark the hole for substrate mounting through a hole in base of the mounting bracket. The dowel in-

cluded in the scope of delivery is suitable for installation in concrete, stone and masonry. Drill a hole

of Ø 8 mm and deeper than 50 mm into the substrate and insert the dowel into the hole. In case

of wooden substrates the mounting bracket can directly fixed using the supplied screw, without the

dowel. In case of hardwood the holes may require pre-drilling with Ø 3 mm.

Position the mounting bracket over the dowel, orientate it into the desired direction and screw it

down with the supplied screw.

Now, the clarios eco can be attached to the mounting bracket.

1. Thread a snap ring onto a screw, insert it through a hole at the upper end of the mounting

bracket, thread a plastic washer onto the screw and screw it laterally into the threaded holes on

the luminary housing. In order to do so, insert the spot in the mounting bracket.

2. Repeat that with the second screw, snap ring and plastic washer on the other side.

3. Pay attention to correct sorting: screw head, snap ring, mounting bracket, plastic washer, lumi-

nary housing.

4. Orientate the spot in the desired direction and screw it tight with a 4 mm hex key.