Dot-Spot clarios eco 10 W Посібник оператора - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник оператора для У центрі уваги Dot-Spot clarios eco 10 W. Dot-Spot clarios eco 10 W 15 сторінок.
Друкувати сторінку
Configurations
Electrical connection
Order
clarios eco 6 Watt
number
5 m PUR-
cable, with
.33
open cable
end
0,3 m with
.41
M12 plug
5 m PUR-
cable with
.42
M12 plug
Optional accessories
Order number
ground spike ES 20
93000
marten repellent MS
93001
installation extension
93201
MV
dazzle protection BS
93104
eco
Safety
Intended use
The garden and object spots clarios eco are designed for providing effect lighting for plants and
objects as well as for permanent installation. They are designed for operating in moderate climatic
zones and under water (depth 1 m). The luminary is meant for operating with protective low voltage.
In case of detailed lighting planning, please request the light distribution curves (LDC).
Installation to be carried by an expert
The installation may only be carried out by appropriately trained professionals.
Safety instructions
During installation, the relative safety regulations have to be followed. The spot is operated with
protective low voltage of 24 DC. To avoid danger and failures, prior or any work at the spot or instal-
lation, disconnect the power supply from the mains. The spot can't be opened. Connect the sport
only to power supplies with a maximum output voltage of 24 V DC. A wrong voltage may destroy the
spot and the power supply.
20
clarios eco 10 Watt
Dimmable
length 50 cm
length 10 cm, for raised assembly
stainless steel, put on from outside
Safety
Safety instructions
Observe the installation manual of the power supply. Do not overload the power supply! The overall
power consumed by all consumers connected to the power supply should be approx. 10% lower
than the rated power of the power supply being used.
In order to protect the exposed connection cable from rodents it should be protected against mar-
tens (see installation accessories).
High ambient temperatures shorten the life of the LED's. Ensure a good heat dissipation in order to
guarantee a long life of the LED. During operation, do not expose the spot to ambient temperatures
of > 45°C. Do not cover the spot, provide free air circulation.
Do not open the housing of the luminary. The tightness of the clarios eco is only guaranteed if also
the outer sheath of the connection cable is undamaged and if the connection cable is bonded in a
waterproof way. Otherwise, because of the capillary effect, the penetrating moisture can reach and
destroy the electronics of the spot.
Assembly
Preparation
Depending on the configuration, unpack all the parts included in the scope of delivery and check
them for completeness and intactness.
Dispose of the packaging material no longer needed in accordance with applicable regulations.
If you notice any damage from transport, immediately contact the dealer where you purchased the
luminary.
Mechanical installation
Mark the hole for substrate mounting through a hole in base of the mounting bracket. The dowel in-
cluded in the scope of delivery is suitable for installation in concrete, stone and masonry. Drill a hole
of Ø 8 mm and deeper than 50 mm into the substrate and insert the dowel into the hole. In case
of wooden substrates the mounting bracket can directly fixed using the supplied screw, without the
dowel. In case of hardwood the holes may require pre-drilling with Ø 3 mm.
Position the mounting bracket over the dowel, orientate it into the desired direction and screw it
down with the supplied screw.
Now, the clarios eco can be attached to the mounting bracket.
1. Thread a snap ring onto a screw, insert it through a hole at the upper end of the mounting
bracket, thread a plastic washer onto the screw and screw it laterally into the threaded holes on
the luminary housing. In order to do so, insert the spot in the mounting bracket.
2. Repeat that with the second screw, snap ring and plastic washer on the other side.
3. Pay attention to correct sorting: screw head, snap ring, mounting bracket, plastic washer, lumi-
nary housing.
4. Orientate the spot in the desired direction and screw it tight with a 4 mm hex key.
21