- ページ 5
トラクター Carco 30BのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Carco 30B 11 ページ。 For ji case 650k/750k/850k
MOUNTING GROUP
INSTALLATION INSTRUCTIONS:
1. Observe general service methods and safety precau-
tions given in Case / New Holland Tractor Service
Manual.
2. Dimensions in inches (mm).
3. PTO rotation is counter-clockwise (CCW) as viewed
from the rear of the tractor.
4. Remove paint, rust, dirt and oil from mounting sur-
faces of tractor, winch and winch mounting brackets.
Clean threads in mounting fastener holes in winch
and rear face of tractor. Use a tap if necessary. Make
certain all mounting fastener holes are clean and dry.
5. Tighten all fasteners to the torque valves listed in the
following chart, unless otherwise noted.
TORQUE SPECIFICATIONS
FASTENER SIZE
TORQUE (FT-LB)
3/4 - 10 UNC, GR8
1/2 - 13 UNC GR8
5/16 - 24 UNF GR8
M20X2.5 GR10.9
M12X1.75 GR10.9
6. Remove (8) shipping fasteners from the front face of
the winch (outer 2 bolts on each side of top and bot-
tom rows of bolts).
7. Apply Loctite 243 or equivalent to the clean, dry
threads of studs (items 15 & 18), and install into the
winch such that the studs bottom out in the holes. If
the studs supplied have a heavier chamfer on one
end, install the end with the heavier chamfer into the
winch. The studs MUST bottom out in the holes
CAUTION
Each mounting bracket weights approximately 95
lbs. (43 kg). Use proper safety precautions when
handling to prevent injury.
8. Test fit the winch mounting brackets (items 1 & 2) to
the winch. Check for interference between the brack-
ets and winch adapter casting, specifically near the
winch center. Lightly grind the brackets and winch
adapter casting as required to provide the clearance
needed to allow the mounting brackets to bolt flush to
the winch.
TORQUE (N-M)
280
379
80
108
18
25
340
460
74
100
.
9. Remove any installed accessories from the rear face
that will interfere with winch mounting. Remove the
tractor rear cover and retain the bolts for later use.
Remove the small PTO cover from the tractor rear
cover and retain the bolts for later use.
10. Assemble the retaining ring (item 5) into the yoke
(item 4) as shown.
11. Coat the splines of the tractor PTO shaft and the yoke
(item 4) with multi-purpose grease. Install the yoke
onto the tractor shaft as shown.
12. Install the large washer (item 6) against the retaining
ring. Then install the smaller washer (item 14) onto
the bolt.
Apply Loctite 243 or equivalent to bolt
threads.
13. Attach the driveshaft (item 3) to the yoke assembly as
shown, using the cap and bolt kit (item 8). Apply
Loctite 243 or equivalent to the bolt threads.
14. Guide driveshaft through PTO access opening in trac-
tor rear cover and reinstall the rear cover to the trac-
tor using the existing fasteners. Do not replace fas-
teners that will interfere with the winch mounting
brackets.
15. Ensure that the driveshaft is fully retracted and resting
on the bottom of the PTO access opening in the trac-
tor rear cover.
CAUTION
Each mounting bracket weighs approximately 95 lbs.
(43 kg). Use proper safety precautions when handling
to prevent injury.
16. Install the winch mounting brackets (item 1 & 2) to the
tractor rear face as shown, using capscrews (items 11
& 13) and washers (items 12 & 14).
mounting bolts per note 5.
A CARCO 30B winch weighs approximately 1,000
lbs. (454 kg) without oil, cable, tractor adapters and
accessories. Make certain your lifting equipment has
adequate capacity. Attempting to lift the winch with
inadequate equipment may result in personal injury or
damage to the winch or property.
5
MOUNTING GROUP
Torque the