Carco 30B Kurulum Kılavuzu - Sayfa 5

Traktör Carco 30B için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Carco 30B 11 sayfaları. For ji case 650k/750k/850k

Sayfayı Yazdır

MOUNTING GROUP

INSTALLATION INSTRUCTIONS:

1. Observe general service methods and safety precau-

tions given in Case / New Holland Tractor Service

Manual.

2. Dimensions in inches (mm).

3. PTO rotation is counter-clockwise (CCW) as viewed

from the rear of the tractor.

4. Remove paint, rust, dirt and oil from mounting sur-

faces of tractor, winch and winch mounting brackets.

Clean threads in mounting fastener holes in winch

and rear face of tractor. Use a tap if necessary. Make

certain all mounting fastener holes are clean and dry.

5. Tighten all fasteners to the torque valves listed in the

following chart, unless otherwise noted.

TORQUE SPECIFICATIONS

FASTENER SIZE

TORQUE (FT-LB)

3/4 - 10 UNC, GR8

1/2 - 13 UNC GR8

5/16 - 24 UNF GR8

M20X2.5 GR10.9

M12X1.75 GR10.9

6. Remove (8) shipping fasteners from the front face of

the winch (outer 2 bolts on each side of top and bot-

tom rows of bolts).

7. Apply Loctite 243 or equivalent to the clean, dry

threads of studs (items 15 & 18), and install into the

winch such that the studs bottom out in the holes. If

the studs supplied have a heavier chamfer on one

end, install the end with the heavier chamfer into the

winch. The studs MUST bottom out in the holes

CAUTION

Each mounting bracket weights approximately 95

lbs. (43 kg). Use proper safety precautions when

handling to prevent injury.

8. Test fit the winch mounting brackets (items 1 & 2) to

the winch. Check for interference between the brack-

ets and winch adapter casting, specifically near the

winch center. Lightly grind the brackets and winch

adapter casting as required to provide the clearance

needed to allow the mounting brackets to bolt flush to

the winch.

TORQUE (N-M)

280

379

108

340

460

100

9. Remove any installed accessories from the rear face

that will interfere with winch mounting. Remove the

tractor rear cover and retain the bolts for later use.

Remove the small PTO cover from the tractor rear

cover and retain the bolts for later use.

10. Assemble the retaining ring (item 5) into the yoke

(item 4) as shown.

11. Coat the splines of the tractor PTO shaft and the yoke

(item 4) with multi-purpose grease. Install the yoke

onto the tractor shaft as shown.

12. Install the large washer (item 6) against the retaining

ring. Then install the smaller washer (item 14) onto

the bolt.

Apply Loctite 243 or equivalent to bolt

threads.

13. Attach the driveshaft (item 3) to the yoke assembly as

shown, using the cap and bolt kit (item 8). Apply

Loctite 243 or equivalent to the bolt threads.

14. Guide driveshaft through PTO access opening in trac-

tor rear cover and reinstall the rear cover to the trac-

tor using the existing fasteners. Do not replace fas-

teners that will interfere with the winch mounting

brackets.

15. Ensure that the driveshaft is fully retracted and resting

on the bottom of the PTO access opening in the trac-

tor rear cover.

CAUTION

Each mounting bracket weighs approximately 95 lbs.

(43 kg). Use proper safety precautions when handling

to prevent injury.

16. Install the winch mounting brackets (item 1 & 2) to the

tractor rear face as shown, using capscrews (items 11

& 13) and washers (items 12 & 14).

mounting bolts per note 5.

A CARCO 30B winch weighs approximately 1,000

lbs. (454 kg) without oil, cable, tractor adapters and

accessories. Make certain your lifting equipment has

adequate capacity. Attempting to lift the winch with

inadequate equipment may result in personal injury or

damage to the winch or property.

MOUNTING GROUP

Torque the