- ページ 2

セキュリティセンサー DPM KC098のPDF マニュアルをオンラインで閲覧またはダウンロードできます。DPM KC098 2 ページ。 Intelligent stud scanner

ページを印刷する

KC098

Mode switcher – set the mode for wood joists AC

live wires or metal objects.

Power button – the scanner connects to power

supply when pressing this button.

LCD – indicates detecting mode and detecting

result.

Marker slot – indicates the edge of the detected

object.

Beeps aperture – the beeps will ring when cali-

brating or detecting the target object.

Caution symbol for live wires – the symbol is on

when detecting electric live wires.

Indication symbol for low battery – The light is on

when the battery is low, please replace with new

battery according to instructions.

Indication symbol for approaching the target ob-

ject – the two symbols will light in turn towards

the center symbol when approaching the edge of

the detected object.

Metal detecting, indication – the light indicates

that the current detecting mode is on metal

object.

10.

AC detecting indication – the light indicates that

the current detecting mode is on AC live wire.

11.

Wood detecting indication – the light indicates

that the current detecting mode is on wood joist.

12.

Symbol for central arrow – the light is on when

detecting the edge of the detected object.

OVERVIEW

Intelligent Stud Scanner can be automatically cali-

brated with sensitive induction after starting up. Se-

lect mode for joists, AC live wires or metal detection

through the function selection switcher. Once the

edges of joists, AC live wires or metals are detected,

the scanner will send out sound indication and you

can easily mark the central position of the target on

the measured surface through the marker slot on top

of the tool with pencil.

TECHNICAL SPECIFICATIONS

Parameters

Values

Wood joists, AC live

Object of detection

wires and Metals

Detection capability

Wood joists – thickness of wall is ¾ inches

Metals – 1 ½ inches deep away

AC live wires (AC) – 2 inches

deep away from the wall

Power supply

A 9 Volt block battery

Type of back light

LED

Operation temperature +5°C – +40°C

Dimensions

180 x 75 x 30 mm

Weight

0,17 kg

OPERATION INSTRUCTIONS

Battery

Open the battery compartment door on the back of

the scanner, and plug one 9 Volt block battery into

the battery connector and put the battery back to the

compartment. Close the battery compartment door.

Calibration

The tool should be calibrated on the surface of the

detected object before detecting or after function

switch's diversion.

Detecting calibration for wood studs

Set the mode switcher to the mode for wood stud

and then lightly adhere the scanner to the detected

surface, press the power button to connect to the

power supply, the scanner will send out sound indi-

cation and be calibrated automatically according to

the thickness of the detected wall. The calibration

is finished when the sound stops. You can process

wood stud detection now and please always press

the power button during the detecting course.

Notice:

When calibrating, the scanner cannot be di-

– DETEKTOR METALI I PRZEWODÓW / INTELLIGENT STUD SCANNER

rectly put on the materials with high density (e.g.

metals, wood joists), or wet, new–painted and

mountable places. Restart calibration by chang-

ing another place.

When approaching or detecting the AC live wire

during calibration the camion symbol for live

wires will indicate after calibration.

Detecting calibration for AC live wires

Set the mode switcher to the mode for AC live wire,

and then calibrate the tool with reference to the

method of "detecting, calibration for wood stud".

Notice:

When calibrating, the tool will automatically set the

degree of induction according to the distance to the

live wire. If distance to the AC live wire is far enough.

the induction will be set to the strongest degree, if

close to the AC live wire, the tool will automatically

set to the most ideal induction according to the dis-

tance.

Detecting calibration for metal objects

Set the mode switcher to the mode for metal ob-

ject, and then calibrate the tool with reference to the

method of "detecting calibration for wood stud".

Notice:

When calibrating, the tool will automatically set

the degree of induction according to the exist-

ence of the metal object. If no metal object exists,

the induction will be set to the strongest degree,

if metal object exists the tool will automatically

set to the most ideal induction according to the

type and size of the metal object.

When approaching or detecting the AC live wire

during calibration, the caution symbol for live

wires will indicate after calibration.

Operation

Wood stud detection – detecting wood joists through

walls

According to the calibration requirements for wood

stud detection, calibrate the tool to the ideal induc-

tion degree and process as per the following steps:

a. Move the tool across the surface of the object in

straight line horizontally and slowly, and hold the

tool firmly against the surface.

b. When the tool moves horizontally and is close to

the detected object, the outer side of arrow symbol

will illumine and then slow down the moving speed

and the arrow lights of both sides will light in turn

towards the center light (if the arrow symbols of

both sides go out when moving, reset automatic

calibration and detection from another place).

c. If the edge of wood joists we detected, the

center arrow symbol will illumine and the beeps

will rings, at this time, make a mark on edge of

detected object through the marker slot by pen-

cil. Then continue to move the unit slowly in the

same way until the arrow symbol goes out and

the beeps stop.

d. Repeat the steps above from the opposite direc-

tion to detect the other edge of the target object

and make a mark the center of the two markers is

just the center of the detected object. Repeat the

operations for several times to get the relatively

precise result.

Notice: if the power button released incautiously

you must restart the calibration and repeal the steps

above to detect.

AC live wire detection – detecting the AC live wire

through walls

a. According to the calibration requirements for AC

live wire detection, calibrate the tool to the ideal

induction.

Importer: DPm Solid Polska, ul. Harcerska 34, 64-600 Oborniki Kowanówko

tel. +4861 2965 470 fax +4861 2967 476 www.solid-polska.pl [email protected]

INFORmACJE O OCHRONIE śRODOWISKA I ZAGOSPODAROWANIU ODPADAmI

Należy zapoznać się z lokalnymi zasadami zbiórki i segregacji sprzętu elektrycznego i elektronicznego.

Należy przestrzegać przepisów i nie wyrzucać zużytych produktów elektronicznych wraz z normalnymi

odpadami gospodarstwa domowego. Prawidłowe składowanie zużytych produktów pomaga ograniczyć

ich szkodliwy wpływ na środowisko naturalne i zdrowie ludzi.

b. Operate the tool and find out the two edges of AC

live wires and make a mark with reference to the

method of "Wood stud detection detecting wood

joists through walls".

c. The center of the two marks is just the center of

AC live wire.

Notice: AC live wires in metal pipes or metal covered

wire, as well as metal walls or walls of high density

can't be detected.

Metal object detection – detecting the metal stud

through walls

a. According to the calibration requirements for

metal stud detection, calibrate the tool to the

ideal induction.

b. Operate the tool and find out the two edges of

metal studs and make a mark with reference to

the method of "Wood stud detection – detecting

wood joists through walls".

c. The center of the two marks is just the center of

metal stud.

TIPS ON OPERATION

Using new battery

Check the battery before operation. When the bat-

tery is low, the

symbol will blink continuously on

the screen after calibration. Replace with new bat-

tery according to instructions.

Recommendation

In order to make sure that the scanner is on the best

state during detection, hold the tail of the tool when

operation and keep the other hand at least 6 inches

away from the tool during detection.

TIPS

A. The tool can accurately detect the center of the

target object, but the width of the target object

can only be detected in a range.

B. Please do not use the tool near strong electric

wave or high frequency interference.

C. Please do not use the scanner in high tempera-

ture and wet place.

D. Please try to avoid using the tool on wet plate

and wall.

E. Sometimes, the scanner cannot detect the slate

or mixed plate correctly because the density of

the materials change a lot.

F. When tacking, cutting or drilling on the wall, ceil-

ing or floor, please lake care to the wires and

pipes on the back of them.

G. The covered wires, useless wires, telephone

lines, CATV wires and circuitries without electric-

ity could not be detected as live wires.

H. When the thickness of detected wall is over ¾

inches or the wood joists are close to each other,

wood stud detection is not suitable. Generally,

the space between wood joists is 16 or 24 inch-

es, and the width of the joist is 1 ½ inches.

I. The detection is not suitable for metal wall or the

metal materials in the wall distribute too thick.

J. When constructing beside the AC live wires, the

power supply should be switched off.

CAUTIONS

•

Operate with care and do not let the tool drop

down.

•

Do not disassemble the tool in case of damage.

•

Do not place the tool with workbox.

•

Avoid rain and water.

•

Do not keep the tool under the temperature of

above 50º C.

•

Clean the tool gently with soft fabric.

•

Remove the battery when not in use for an ex-

tended period of time in case of damage of tool

by deterioration of battery.

2009/05/IN25