- ページ 15

食器洗い機 Bosch DISHWASHERのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch DISHWASHER 46 ページ。 Dishwasher bosch
Bosch DISHWASHER にも： 取扱説明書 (30 ページ), 取付説明書 (34 ページ), 取扱説明書 (30 ページ), 取扱説明書 (28 ページ), 取扱説明書 (30 ページ), 取扱説明書 (38 ページ), 取扱説明書 (42 ページ), 取扱説明書 (32 ページ), 取扱説明書 (36 ページ), 取扱説明書 (30 ページ), 取扱説明書 (24 ページ), 取扱説明書 (26 ページ), 取扱説明書 (40 ページ), 取扱説明書 (28 ページ), 取扱説明書 (29 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ), 取付説明書 (50 ページ), 取付説明書 (20 ページ), 操作方法 (24 ページ), 操作説明 (36 ページ), 取扱説明書 (25 ページ), 取扱説明書 (31 ページ)

ページを印刷する
Bosch DISHWASHER 取扱説明書

Operating the Dishwasher

Start the dishwasher
Open the door and press the [On/Off] button. The LED of the last selected cycle flashes.
1
Select a cycle and desired options.
2
Press [Start] and close the door to begin the cycle.
3
Cancel a cycle
Open the door just far enough to expose the control panel. Be careful of hot water that may splash out.
1
Press and hold the [Start] button for approximately 3 seconds until the display reads "0:01".
2
Close the door and wait about 1 minute while the dishwasher drains.
3
Open the door and press the [On/Off] button.
4
Interrupt a cycle
Open the door just far enough to expose the control panel. Be careful of hot water that may splash out.
1
Press the [On/Off] button to turn the unit off.
2
To resume the cycle, press the On/Off button and close the dishwasher door.
3
Setting the amount of rinse aid
The amount of rinse aid dispensed can be set from "r:00" to "r:06".
To change the setting:
Open the door and press the [On/Off] button.
1
Hold down the "A" button (see page 4) and press [Start] until the display indicates "H:00".
2
Release both buttons.
3
Press the "A" button until the display shows "r:05".
4
Press the "C" button to select the desired setting.
5
"r:00" = dispenser is OFF
"r:01" = lowest setting
"r:02" = low setting
"r:03" = medium setting
"r:04" = medium/high setting
"r:05" = high setting
"r:06" = highest setting
Press [Start] to save the setting and close the door.
6
InfoLight
An LED illuminates the floor to indicate the unit is running. If the appliance is installed at eye-level, the LED is not visible.
To change the setting:
Open the door and press the [On/Off] button.
1
Hold down the "A" button (see page 4) and press [Start] until the display indicates "H:00".
2
Release both buttons.
3
Press the "A" button until the display shows "1:01".
4
Press the "C" button to switch between "1:01" = ON and "1:00" = OFF and press [Start] to save.
5
Delay Start
You can delay the start of the cycle in one hour increments up to 24 hours.
To set delay start:
Open the door and press the [On/Off] button.
1
Press the [+] button until the display jumps to "h:01".
2
Press the [+] or [-] button until the displayed time corresponds with your requirements.
3
h:01 = 1 hour delay
h:24 = 24 hour delay
Press [Start] to activate delay start.
4
To cancel delay start:
Press the [+] or [-] button until "h:00" is indicated on the digital display.
1
Press [Start] to save setting and close the door.
2
13