- ページ 3

食器洗い機 Bosch SGE63E15UCのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Bosch SGE63E15UC 38 ページ。 24" recessed handle special application
Bosch SGE63E15UC にも：サプリメント (2 ページ), 取付説明書 (40 ページ), 取扱説明書 (40 ページ), 取扱説明書 (40 ページ), 取扱説明書 (44 ページ), パンフレット＆スペック (3 ページ), 取扱説明書 (40 ページ)

ページを印刷する

Avoiding General Hazards

Do not use the dishwasher until it is completely

installed. When opening the door on an uninstalled

dishwasher, carefully open the door while supporting

the rear of the unit. Failure to follow this warning can

cause the dishwasher to tip over and result in serious

injury.

Before installing the "L"-shaped supplied countertop

mounting brackets (select models), decide which

method will be used to secure the dishwasher into its

opening. Once these mounting brackets are installed

on the dishwasher, removing them is difficult and will

damage the mounting brackets and the dishwasher.

In some conditions, hydrogen gas can form in a hot

water system that has not been used for weeks.

Hydrogen gas is explosive.

Before filling a dishwasher from a system that has

been off for weeks, run the water from a nearby faucet

in a well ventilated area until there is no sound or evi-

dence of gas.

Temperatures required for soldering and sweating will

damage the dishwasher's base and water inlet valve.

If plumbing lines are to be soldered or sweated, keep

the heat source at least 6" (152.4 mm) away from the

dishwasher's base and water inlet valve.

Removing any cover or pulling the dishwasher from the

cabinet can expose hot water connections, electrical

power and sharp edges or points. Handle with care.

Avoiding Electrical Shock/Fire Hazards

Do not allow the electrical and water supply lines to

touch. Separate channels are provided under the

dishwasher.

Do not work on an energized circuit. Doing so could

result in serious injury or death. Only qualified electri-

cians should perform electrical work. Do not attempt

any work on the dishwasher electric supply circuit

until you are certain the circuit is de-energized.

WARNING

Make sure electrical work is properly installed. There

should be no loose electrical connections. Ensure all

electrical connections are properly made.

The customer has the responsibility of ensuring that the

dishwasher electrical installation is in compliance with

all national and local electrical codes and ordinances.

The dishwasher is designed for an electrical supply

of 120V, 60 Hz, AC, connected to a dishwasher-

dedicated, properly grounded electrical circuit with a

fuse or breaker rated for 15 amps. Electrical supply

conductors shall be a minimum #14 AWG copper only

wire rated at 75°C (167°F) or higher.

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or

lead on the appliance. Do not use extension cords.

Avoiding Plumbing/Scalding Hazards

Do not perform any work on a charged hot water line.

Serious injury could result. Only qualified plumbershould

perform plumbing work. Do not attempt any work on

the dishwasher hot water supply plumbing until you

are certain the hot water supply is shut off.

Do not over tighten the 90° elbow. Doing so may

damage the water inlet valve and cause a water leak.

Temperatures required for soldering and sweating

will damage the dishwasher's water inlet valve. If

plumbing lines are to be soldered or sweated, keep

the heat source at least 6" (152.4 mm) away from the

dishwasher's water inlet valve.

Check local plumbing codes for approved plumbing

procedures and accessories. All plumbing should be

done in accordance with national and local codes.

These instructions depict an installation method for

stainless steel braided hose or PEX hot water supply

lines. If using copper tubing or other material for

water supply, defer to a licensed plumber for proper

installation.