- ページ 8

投影スクリーン Draper Nocturne+ EのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Nocturne+ E 12 ページ。 Outdoor electric projection screen

ページを印刷する

Nocturne+ E

Section 5 - Limit Adjustments

Please Note: Screen limits

are factory set for optimum

performance. Any adjustment of

these limits could void the warranty.

Please check with Draper prior to

resetting screen limits.

Please Note: If Screen is "Right

Hand Motor" the WHITE/DOWN

and YELLOW/UP

limit screws

(II)

are reversed

(Fig. 7)

Figure 7

CAUTION:

Motor

- Be sure all switches

End

are in "off" position

before adjusting limit

switches.

- Be prepared to shut off

manually while testing.

- Screen may be

Standard Roll

damaged by lowering

Left hand motor:

it too far and

White Socket—Down

Yellow Socket—Up

exposing roller.

Right hand motor:

- Motor must be

White Socket—Up

Yellow Socket—Down

installed so that limit

switches are pointed

down.

Section 6 - RF Remote Programming Instructions

IMPORTANT: This section ONLY applies if optional RTS Motor has been ordered.

Please Note: The motor ships with no programming. Follow these instructions to program unit to the desired transmitter.

Pen

Programming

Button

Setting an Intermediate Stop -

Screen MUST BE in USER mode.

Pen

Programming

Button

BACK

(Standard Motors)

Figure 6

DOWN Limit

Clockwise

decreases

down travel.

(I)

UP Limit

Counterclockwise

increases up

travel.

Motor

End

n c

c k

d i e

B a

A u

d e

S i d

S i

Reverse Roll

Left hand motor:

White Socket—Down

Yellow Socket—Up

Right hand motor:

White Socket—Up

Yellow Socket—Down

CAUTION: DO NOT allow dowel to

wrap over roller when operating screen!

This could damage screen.

1. Select a transmitter channel to assign motor. Hold UP and DOWN

2. Check motor direction. To reverse motor direction, hold MY/STOP

3. Move motor to upper limit position. Hold MY/STOP and DOWN

STOP

4. While motor is at lower limit, hold UP and MY/STOP buttons until

DOWN

LED Lights

5. Next, hold MY/STOP button until motor jogs.

Channel

6. Put motor into USER MODE by holding small programming button

Selector

1. Move screen to desired mid-point location and

hold MY/STOP button until motor jogs.

2. To test, press the MY/STOP button when

motor is standing still. The screen will move to

that intermediate location.

3. To delete an intermediate stop, go to the

intermediate stop and hold the MY/STOP

button until motor jogs.

Add a Channel -

Screen MUST BE in USER mode.

1. Select channel currently operating

motor, then hold programming

button until motor jogs.

2. Select new channel to add to

motor, then hold programming

button until motor jogs.

3. The motor should now work on

both old and new channel.

"Down" Limit Adjustment

To Reduce Screen Drop:

(I)

1. Raise screen surface approximately 1'

2. Turn DOWN

limit screw clockwise

(I)

3. Test by lowering screen. Repeat steps 1 & 2 until desired position

is reached.

To Increase Screen Drop:

1. Lower screen to down limit.

(II)

2. With down switch on, turn DOWN

(3 screw turns = ½ roller revolution)

3. Test by raising screen approximately 1'

4. Repeat steps 2 and 3 until desired position reached.

Please Note: For Quiet Motor with alternate limit screws:

WHITE screw = UP and RED screw = DOWN.

"Up" Limit Adjustment

If Screen Raises Too High:

1. Lower screen surface approx. 1'

2. Turn UP

limit screw clockwise

(II)

3. Test by advancing screen up.

4. Repeat steps 1 through 3 until desired position is reached.

If Screen Needs to Raise Higher:

1. Lower screen surface approx. 1'

2. With UP switch on, turn UP

(3 screw turns = 1/2 roller revolution)

3. Repeat steps 1 and 2 until desired position is reached.

(ONLY used if optional RTS Motor is speciﬁed)

buttons until motor jogs, then release.

button for 5 seconds until motor jogs. Check direction again.

buttons until motor moves down, then release. Use UP and DOWN

buttons to move screen to correct lower limit and press MY/STOP.

motor moves up, then release. The screen should move to upper

limit and stop.

on the back of transmitter and waiting for motor to jog.

upper or

lower limit

Delete a Channel -

Screen MUST BE in USER mode.

1. Select channel operating motor

desired, then hold programming

button until motor jogs.

2. Select channel to remove, then

hold programming button until

motor jogs. Motor should now

only work on channel kept from

Step 1.

page 8 of 12

(requires 5/32" (4mm) Allen wrench)

above desired setting and turn off.

(30cm)

(3 screw turns = 1/2 roller revolution)

limit screw counterclockwise

(I)

to increase drop.

then lower to new down limit.

(30cm)

(Fig. 10)

below desired setting and turn off.

(30cm)

(3 screw turns = ½ roller revolution).

below desired setting and turn off.

(30cm)

limit screw counterclockwise

(II)

Adjust Limits in User Mode

1. Move motor to limit

to be changed. Screen must move

to previously set limit and will stop

automatically.

2. Hold UP and DOWN buttons until motor

jogs.

3. Move motor to its new limit location and

hold MY/STOP button until motor jogs.

Reset Motor

1. Disconnect for 3 seconds,

reconnect for 10 seconds,

disconnect for 3 seconds.

Screen will roll.

2. Hold program button on

remote and wait for 2

separate jogs.

Motor is now reset.

(upper or lower)