Draper Nocturne+ E Installatie- en bedieningsinstructies - Pagina 8
Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Draper Nocturne+ E. Draper Nocturne+ E 12 pagina's. Outdoor electric projection screen
Pagina afdrukken
Nocturne+ E
Section 5 - Limit Adjustments
Please Note: Screen limits
are factory set for optimum
performance. Any adjustment of
these limits could void the warranty.
Please check with Draper prior to
resetting screen limits.
Please Note: If Screen is "Right
Hand Motor" the WHITE/DOWN
and YELLOW/UP
limit screws
(II)
are reversed
.
(Fig. 7)
Figure 7
CAUTION:
Motor
- Be sure all switches
End
are in "off" position
before adjusting limit
switches.
- Be prepared to shut off
manually while testing.
- Screen may be
Standard Roll
damaged by lowering
Left hand motor:
it too far and
White Socket—Down
Yellow Socket—Up
exposing roller.
Right hand motor:
- Motor must be
White Socket—Up
Yellow Socket—Down
installed so that limit
switches are pointed
down.
Section 6 - RF Remote Programming Instructions
IMPORTANT: This section ONLY applies if optional RTS Motor has been ordered.
Please Note: The motor ships with no programming. Follow these instructions to program unit to the desired transmitter.
Pen
Programming
Button
Setting an Intermediate Stop -
Screen MUST BE in USER mode.
Pen
Programming
Button
BACK
(Standard Motors)
Figure 6
+
DOWN Limit
I
Clockwise
decreases
down travel.
(I)
UP Limit
+
lI
Counterclockwise
increases up
travel.
Motor
End
e
n c
c k
d i e
B a
A u
e
d e
S i d
S i
Reverse Roll
Left hand motor:
White Socket—Down
Yellow Socket—Up
Right hand motor:
White Socket—Up
Yellow Socket—Down
CAUTION: DO NOT allow dowel to
wrap over roller when operating screen!
This could damage screen.
1. Select a transmitter channel to assign motor. Hold UP and DOWN
2. Check motor direction. To reverse motor direction, hold MY/STOP
3. Move motor to upper limit position. Hold MY/STOP and DOWN
UP
STOP
4. While motor is at lower limit, hold UP and MY/STOP buttons until
DOWN
LED Lights
5. Next, hold MY/STOP button until motor jogs.
Channel
6. Put motor into USER MODE by holding small programming button
Selector
1. Move screen to desired mid-point location and
hold MY/STOP button until motor jogs.
2. To test, press the MY/STOP button when
motor is standing still. The screen will move to
that intermediate location.
3. To delete an intermediate stop, go to the
intermediate stop and hold the MY/STOP
button until motor jogs.
Add a Channel -
Screen MUST BE in USER mode.
1. Select channel currently operating
motor, then hold programming
button until motor jogs.
2. Select new channel to add to
motor, then hold programming
button until motor jogs.
3. The motor should now work on
both old and new channel.
"Down" Limit Adjustment
To Reduce Screen Drop:
:
(I)
1. Raise screen surface approximately 1'
2. Turn DOWN
limit screw clockwise
(I)
3. Test by lowering screen. Repeat steps 1 & 2 until desired position
is reached.
To Increase Screen Drop:
1. Lower screen to down limit.
:
(II)
2. With down switch on, turn DOWN
(3 screw turns = ½ roller revolution)
3. Test by raising screen approximately 1'
4. Repeat steps 2 and 3 until desired position reached.
Please Note: For Quiet Motor with alternate limit screws:
WHITE screw = UP and RED screw = DOWN.
"Up" Limit Adjustment
If Screen Raises Too High:
1. Lower screen surface approx. 1'
2. Turn UP
limit screw clockwise
(II)
3. Test by advancing screen up.
4. Repeat steps 1 through 3 until desired position is reached.
If Screen Needs to Raise Higher:
1. Lower screen surface approx. 1'
2. With UP switch on, turn UP
(3 screw turns = 1/2 roller revolution)
3. Repeat steps 1 and 2 until desired position is reached.
(ONLY used if optional RTS Motor is specified)
buttons until motor jogs, then release.
button for 5 seconds until motor jogs. Check direction again.
buttons until motor moves down, then release. Use UP and DOWN
buttons to move screen to correct lower limit and press MY/STOP.
motor moves up, then release. The screen should move to upper
limit and stop.
on the back of transmitter and waiting for motor to jog.
upper or
lower limit
Delete a Channel -
Screen MUST BE in USER mode.
1. Select channel operating motor
desired, then hold programming
button until motor jogs.
2. Select channel to remove, then
hold programming button until
motor jogs. Motor should now
only work on channel kept from
Step 1.
page 8 of 12
(requires 5/32" (4mm) Allen wrench)
above desired setting and turn off.
(30cm)
(3 screw turns = 1/2 roller revolution)
limit screw counterclockwise
(I)
to increase drop.
then lower to new down limit.
(30cm)
.
(Fig. 10)
below desired setting and turn off.
(30cm)
(3 screw turns = ½ roller revolution).
below desired setting and turn off.
(30cm)
limit screw counterclockwise
(II)
.
Adjust Limits in User Mode
1. Move motor to limit
to be changed. Screen must move
to previously set limit and will stop
automatically.
2. Hold UP and DOWN buttons until motor
jogs.
3. Move motor to its new limit location and
hold MY/STOP button until motor jogs.
Reset Motor
1. Disconnect for 3 seconds,
reconnect for 10 seconds,
disconnect for 3 seconds.
Screen will roll.
2. Hold program button on
remote and wait for 2
separate jogs.
Motor is now reset.
.
(upper or lower)