- ページ 5

室内装飾品 Draper FlexShade NEXDのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Draper FlexShade NEXD 8 ページ。 Clutch-operated small and large hardware
Draper FlexShade NEXD にも：取付・取扱説明書 (6 ページ), 説明書インストールと操作 (8 ページ), 説明書インストールと操作 (8 ページ), 説明書インストールと操作 (10 ページ), 取扱説明書 (12 ページ)

ページを印刷する

Clutch-Operated FlexShade

Small and Large Hardware

Section 4 - Spring Assist Option

1. Remove the safety screw and slide from the top idler

endcap. Retain these pieces for later

2. Install the Roller Assembly:

Install tube onto clutch

Fig. 7-A:

Swing the idler end into place, then slide the

Fig. 7-B:

idler end spear into the receiver. It may be necessary to

compress the spring-loaded spear.

Caution: The retaining clip must be installed around

the idler-end shaft as shown to prevent the roller

assembly from moving left or right during operation,

and to ensure that the spring-loaded shaft does not

retract into the mechanism in case of a bearing failure.

3. Replace Slide and Safety Screw. Place into groove at an

angle, slide up, and make sure the bottom of the slide is

hooked into the Receiver

(Fig. 7, reverse order)

Figure 7-A

Tube indentation

must be aligned

with the FLAT side

of the clutch sprocket.

Section 5 - Bead Chain Limits and Safety Device Installation

Attaching Stop Balls

1. Set upper and lower travel limits by installing stop balls to bead chain

P-Clip Cord Tension Device

Please Note: Draper Bead Chain Clutch-Operated shades that do not comply with WMCA/ANSI

Standard A100.1-2012 come with a P Clip cord tension device pre-attached to bead chain

This device must be attached to wall, jamb, or sill so that bead chain is held taut enough that

children cannot pull it away from wall or fit their head into loop.

Spring-Loaded Cord Tension Device

If Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2018, a Spring-Loaded Cord

Tension Device comes installed on bead chain

approved mechanical fasteners

(wood screws)

bead chain away from wall or fit their head into loop.

For more information, visit www.draperinc.com/WindowShades/WCMAcompliance.asp.

1. Install cord tension device to wall, jamb, or sill.

2. Pull tensioner down so that bead chain is held taut and use mounting hardware to keep it taut.

Please Note: Bead chain should be taut enough to move smoothly through device. However, overtightening

screws will damage Spring-Loaded Tension Device.

NEXD,

(Fig. 6)

(crimp closed using pliers) (Fig. 8)

. An approved permanent warning label and

(Fig. 10)

are included. Device is designed so that children cannot pull

(See safety note on page 2)

Figure 6

Figure 7-B

CHAIN LIMITS

1. Attach

stop balls.

(Fig. 9)

Figure 8

Sill

Mount

page 5 of 8

Slide

(RETAIN

FOR

Safety Screw

LATER)

(RETAIN FOR LATER)

Note: Retainer Clip

has extrusion to ﬁt

into slots on shaft.

P-CLIP

P-Clip

2. Crimp

closed

with

pliers.

Figure 9

CHAIN TENSION DEVICE

Jamb

Mount

Tensioner

Figure 10