- ページ 5

室内装飾品 Draper FlexShade NEXDのPDF 説明書インストールと操作をオンラインで閲覧またはダウンロードできます。Draper FlexShade NEXD 8 ページ。 Clutch-operated small and large hardware
Draper FlexShade NEXD にも：取付・取扱説明書 (6 ページ), 説明書インストールと操作 (8 ページ), 取扱説明書 (8 ページ), 説明書インストールと操作 (10 ページ), 取扱説明書 (12 ページ)

ページを印刷する

Clutch-Operated FlexShade

Small and Large Hardware

Section 4 - Pin End Idler

Caution: Do not allow shade roller to become exposed by running shade fabric too far down. Use stop balls provided in

hardware packet by Draper to set up and down travel limits. Stop balls by others may be too small, and become lodged

in clutch mechanism.

Carefully work open

end of roller

(clutch)

onto bead chain

clutch.

Tube indentation

must be aligned

with the FLAT side

of the clutch sprocket.

Test shade to ensure

that roller is level

and operating properly.

If shade is not

level, adjust idler

leveling screw with 3mm

Hex Wrench, available

upon request when

ordering shade.

Please Note: Applying 1-2

drops of a medium-strength

threadlocker to the threads of

the height adjustment screw

is recommended prior to final

adjustment.

Section 5 - Bead Chain Limits and Safety Device Installation

Attaching Stop Balls

1. Set upper and lower travel limits by installing stop balls to bead chain

P-Clip Cord Tension Device

Please Note: Draper

Bead Chain Clutch-Operated shades that do not comply with WMCA/ANSI

Standard A100.1-2012 come with a P-Clip cord tension device pre-attached to bead chain

This device must be attached to wall, jamb, or sill so that bead chain is held taut enough that children

cannot pull it away from wall or fit their head into loop.

Spring-Loaded Cord Tension Device

If Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2018, a Spring-Loaded Cord

Tension Device comes installed on bead chain

mechanical fasteners

(wood screws)

chain away from wall or fit their head into loop.

For more information, visit www.draperinc.com/WindowShades/WCMAcompliance.asp.

2. Pull tensioner down so that bead chain is held taut and use mounting hardware to keep it taut.

1. Install cord tension device to wall, jamb, or sill.

Please Note: Bead chain should be taut enough to move smoothly through device. However, overtightening

screws will damage Spring-Loaded Tension Device.

(Provided with Smaller Shades)

Figure 6-A

Figure 6-C

. An approved permanent warning label and approved

(Fig. 9)

are included. Device is designed so that children cannot pull bead

(See safety note on page 2)

NEXD,

Slide idler end

pin through one

of the slots on

the idler endcap,

and into the

spring-loaded

seat for pin.

Please Note:

See illustration for

different path options.

Please Note:

Idler end has a spring-loaded seat

and detents to prevent the idler pin

from coming out of the idler. It allows

upward and downward adjustment

within the vertical cavity.

(crimp closed using pliers) (Fig. 7)

(Fig. 8)

Please Note: If shade fabric is

uneven, see "Field Adjustments"

on page 2.

Spring-loaded seat

for idler pin

Detents

Figure 7: CHAIN LIMITS

1. Attach

stop balls.

2. Crimp

closed

with

pliers.

Figure 9: CHAIN TENSION DEVICE

Sill

Mount

Tensioner

page 5 of 8

Figure 6-B

Figure 8: P-CLIP

P-Clip

Jamb

Mount