- ページ 10

オーブン Bosch 46 HBN 44のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Bosch 46 HBN 44 28 ページ。 Electric built-in single & double oven
Bosch 46 HBN 44 にも：取扱説明書 (48 ページ), 取扱説明書 (48 ページ), 取付説明書 (28 ページ)

ページを印刷する

ELECTRICAL

SUPPLY

Before installing the oven have a qualified electri-

cian verify that your home is provided with ade-

quate electrical service and that the addition of

the oven will not overload the branch circuit on

which it is to be installed. A separate three-wire

or four-wire single phase, 240 Volt, 60 Hz., or a

208 Volt, 60 Hz. branch circuit is required.

Note:

For use with 208 V, 60 Hz supply voltage

the wiring must be modified as shown in

Connecting to 208 Volt Circuit.

For hook-up

of the oven you will need to have an

approved

junction

box installed

where

it will be

easily

reached

through

the front

of the cabinet

where

the oven will be located.

The oven

has 3

feet of conduit.

Allow two to three feet of slack in

the line so that the oven can be moved

if servicing

is ever

necessary.

DO NOT

shorten

the flexible

conduit.

ELECTRICAL

SHOCK

HAZARD

• The electrical

power

to the oven branch

cir-

cuit must be shut off while line connections

are being made.

• Do not use an extension

cord with this ap-

pliance.

• Electrical

ground

is required

on this appli-

ance. The free end of the green

wire

(the

ground

wire)

must

be connected

to a suit-

able ground.

This

wire

must

remain

grounded

to the

oven.

• If cold water pipe is interrupted

by plastic,

non-metallic

gaskets,

union

connections

other insulating

materials,

DO NOT use for

grounding.

• DO NOT ground

to a gas pipe.

• DO NOT have a fuse in the NEUTRAL

GROUNDING

circuit.

A fuse in the NEU-

TRAL or GROUNDING

circuit could result

in an electrical

shock.

• Check with a qualified

electrician

if you are

in doubt

as to whether

the appliance

properly

grounded.

Failure

to follow

these

instructions

could

re-

sult in serious

injury or death.

WIRING

REQUIREMENTS

When making

the wire connections,

use the entire

length

of the conduit

provided

(3 feet). The con-

duit must not be cut.

Before

making

connections

make

sure the power

is off and read and observe

the following:

A separate

three-wire

or four

wire,

single

phase,

240 Volt,

60 Hz. or 208 Volt, 60 Hz

branch

circuit is required

for the oven.

The oven must

be connected

with COPPER

WIRE ONLY.

In the United

States:

Wiring

must conform

to the National

Electri-

cal Code, ANSI/NFPA

No. 70 latest edition.

You can obtain

a copy of the National

Elec-

trical Code by writing:

National

Fire Protection

Association

Batterymarch

Park

Quincy,

MA 02269

In Canada:

Wiring

must conform

to Canadian

Electrical

Code

C22.1-

latest edition.

You can obtain

copies

of the Canadian

Electrical

Code

writing:

Canadian

Standards

Association

178 Rexdale

Boulevard

Rexdale

(Toronto),

Ontario,

Canada

M9W 1R3

Wire size (COPPER

WIRE ONLY)

and con-

nections

must be suitable

for the rating of the

appliance

per

the National

Electrical

Code

requirements.

The flexible

armored

cable ex-

tending

from

the oven

should

be connected

directly

to the junction

box.

The junction

box should

be located

so as to

allow as much slack as possible

between

the

junction

box and the oven so it can be moved

if servicing

is ever required.

A U.L. listed conduit

connector

must be pro-

vided at each end of the power

supply cable.