Bosch 46 HBN 44 Installation Instructions Manual - Page 10
Browse online or download pdf Installation Instructions Manual for Oven Bosch 46 HBN 44. Bosch 46 HBN 44 28 pages. Electric built-in single & double oven
Also for Bosch 46 HBN 44: Use And Care Manual (48 pages), Use And Care Manual (48 pages), Installation Instructions Manual (28 pages)
Print Page
ELECTRICAL
SUPPLY
Before installing the oven have a qualified electri-
cian verify that your home is provided with ade-
quate electrical service and that the addition of
the oven will not overload the branch circuit on
which it is to be installed. A separate three-wire
or four-wire single phase, 240 Volt, 60 Hz., or a
208 Volt, 60 Hz. branch circuit is required.
Note:
For use with 208 V, 60 Hz supply voltage
the wiring must be modified as shown in
Connecting to 208 Volt Circuit.
For hook-up
of the oven you will need to have an
approved
junction
box installed
where
it will be
easily
reached
through
the front
of the cabinet
where
the oven will be located.
The oven
has 3
feet of conduit.
Allow two to three feet of slack in
the line so that the oven can be moved
if servicing
is ever
necessary.
DO NOT
shorten
the flexible
conduit.
ELECTRICAL
SHOCK
HAZARD
• The electrical
power
to the oven branch
cir-
cuit must be shut off while line connections
are being made.
• Do not use an extension
cord with this ap-
pliance.
• Electrical
ground
is required
on this appli-
ance. The free end of the green
wire
(the
ground
wire)
must
be connected
to a suit-
able ground.
This
wire
must
remain
grounded
to the
oven.
• If cold water pipe is interrupted
by plastic,
non-metallic
gaskets,
union
connections
or
other insulating
materials,
DO NOT use for
grounding.
• DO NOT ground
to a gas pipe.
• DO NOT have a fuse in the NEUTRAL
or
GROUNDING
circuit.
A fuse in the NEU-
TRAL or GROUNDING
circuit could result
in an electrical
shock.
• Check with a qualified
electrician
if you are
in doubt
as to whether
the appliance
is
properly
grounded.
Failure
to follow
these
instructions
could
re-
sult in serious
injury or death.
WIRING
REQUIREMENTS
When making
the wire connections,
use the entire
length
of the conduit
provided
(3 feet). The con-
duit must not be cut.
Before
making
connections
make
sure the power
is off and read and observe
the following:
1.
A separate
three-wire
or four
wire,
single
phase,
240 Volt,
60 Hz. or 208 Volt, 60 Hz
branch
circuit is required
for the oven.
2.
The oven must
be connected
with COPPER
WIRE ONLY.
3.
In the United
States:
Wiring
must conform
to the National
Electri-
cal Code, ANSI/NFPA
No. 70 latest edition.
You can obtain
a copy of the National
Elec-
trical Code by writing:
National
Fire Protection
Association
Batterymarch
Park
Quincy,
MA 02269
In Canada:
Wiring
must conform
to Canadian
Electrical
Code
C22.1-
latest edition.
You can obtain
copies
of the Canadian
Electrical
Code
by
writing:
Canadian
Standards
Association
178 Rexdale
Boulevard
Rexdale
(Toronto),
Ontario,
Canada
M9W 1R3
4.
Wire size (COPPER
WIRE ONLY)
and con-
nections
must be suitable
for the rating of the
appliance
per
the National
Electrical
Code
requirements.
The flexible
armored
cable ex-
tending
from
the oven
should
be connected
directly
to the junction
box.
5.
The junction
box should
be located
so as to
allow as much slack as possible
between
the
junction
box and the oven so it can be moved
if servicing
is ever required.
6.
A U.L. listed conduit
connector
must be pro-
vided at each end of the power
supply cable.