ステレオシステム Anchor BeaconのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Anchor Beacon 2 ページ。 Anchor beacon line array battery-powered, portable line array sound system
Anchor Beacon にも： オーナーズマニュアル (4 ページ), オーナーズマニュアル (4 ページ), オーナーズマニュアル (10 ページ), オーナーズマニュアル (7 ページ), クイック・スタート・マニュアル (2 ページ), クイック・スタート・マニュアル (2 ページ)
ページを印刷する
ANCHOR AUDIO WIRELESS
CHANNEL SELECTION - BUILT-IN RECEIVER
1. Choose any available wireless channel from 1 thru 16
2. Set the Wireless Channel Selection Knob to the channel you choose in step 1
WIRELESS 1 CHANNEL
WIRELESS 2 CHANNEL
SELECTION
SELECTION
WIRELESS 2 RX
WIRELESS 1 RX
INDICATOR LIGHTS
INDICATOR LIGHTS
WIRELESS 1
WIRELESS 2
VOLUME CONTROL
VOLUME CONTROL
OPERATING THE WIRELESS MICROPHONE/TRANSMITTER
CHANNEL SELECTION -
HANDHELD TRANSMITTER
1. Unscrew battery cover on bottom of microphone
2. Set the CHANNEL SELECTOR dial to match the
channel setting of your receiver
3. Replace battery cover and tighten firmly
The wireless RX indicators will light (only one indicator will light at a time) when the wireless signal is being
transmitted and received
AC OPERATION & BATTERY CHARGING/INDICATORS
Beacon Sound Systems includes an automatic charging system designed to properly charge and maintain the
systems built-in batteries. To charge batteries plug the system into an AC outlet and operate as normal while
built-in batteries are charging. The CHARGE STATUS LED will light when charging. Bright red indicates charge
process has begun. Amber indicates the charge process is almost complete, and green indicates full battery.
It takes approximately 7 hours to charge the completely drained Beacon batteries.
SYSTEM STORAGE & BATTERIES
Fully charge batteries before first use and storage. For extended periods of storage either leave systemplugged
into an AC outlet or charge the system at least once each month for a minimum of 24 hours.
BUILT-IN BATTERY MAINTENANCE
To preserve battery life the built-in batteries MUST be FULLY charged before the first use. Regardless of length
of operation, it is recommended that batteries be fully charged as soon as possible after each use.
If you have two wireless
receivers repeat above for the
second receiver. Remember,
each receiver/transmitter
pair must be set to different
channels to avoid interference.
CHANNEL SELECTION -
BODY-PACK TRANSMITTER
1. The channel selection dial is located on the side
of the transmitter
2. Set the CHANNEL selection dial to match the
channel setting of the receiver
OPERATING THE BLUETOOTH TRANSMITTER
POWERING UP THE BLUETOOTH
1. Turn on the Bluetooth with the volume knob (it will
make a boot up noise).
2. Before hooking up your device, take a moment to
go over what the different LED light signals mean:
No light: indicates either Blutooth is off, or it
a.
is in sleep mode, and cannot connect
b.
Blinking light: indicates pairing mode, this is
when you should connect
c.
Solid light: indicates connection, your device
is connected
PAIRING A DEVICE
1. Press the pairing button (it will acknowledge pairing mode with a beep) this mode will last 90 seconds. If no device is
paired within the 90 seconds, the Bluetooth will enter sleep mode.
2. When the Bluetooth module is in pairing mode, it is discoverable and will show up on the selection list of your Bluetooth
enabled device.
3. Select the Bluetooth titled "Anchor Audio" to pair your device with the Anchor Audio Sound System.
4. If a previously paired device is in range and discoverable, the unit should automatically make a connection, however
this may depend on your individual device.
5. When the device has successfully connected to the Bluetooth, the Bluetooth module will beep to signify connection and
the Blue LED will become solid.
6. Now you can play audio from your Bluetooth device to the Anchor Audio Portable Sound System. You can adjust volume
by using the Bluetooth module's knob, as well as the volume control on your device.
Frequently Asked Questions:
What is the range of Anchor Audio Bluetooth?
The Anchor Audio Bluetooth range is 100 ft. line of sight.
My Sound System is auto-connecting to a device, but I don't know which one. Can I disconnect directly from the
Sound System?
Yes, if your unit is auto-connecting to a device that you cannot identify (because for example, you're in a room with other peo-
ple who have connected to the unit in the past), you may need to manually disconnect that pair from the Sound System itself.
Just hold the 'pairing' button for two seconds, and the Sound System will disconnect from the device it is currently connected
to, and immediately go into pairing mode.
What kind of modes can my phone be in that allow the Bluetooth connection to still work?
Bluetooth will work in modes such as Airplane mode and Do Not Disturb (or the equivalent). Just be sure to still have your
Bluetooth setting turned on. To simplify the process, put your phone in the desired mode first, and then secure the Bluetooth
connection, as moving into these modes may cause disconnection.
What happens if I get a phone call?
Incoming and outgoing calls should pause the audio stream. The audio from the call should not be transmitted via Bluetooth.
To avoid interrupting audio, set device in Airplane mode, then enable Bluetooth, ensure your connected, and you should not
encounter any interruptions in your audio stream.
*Bluetooth connection and behavior may depend on your individual device settings and capabilities, all testing was done using an Apple iPhone.
NOTE: All Anchor Audio Sound System Bluetooth connections will be named "Anchor Audio", so if your using multiple systems,
be sure to keep track of each connection.
VOLUME/POWER KNOB
PAIRING
VOLUME
INDICATOR LIGHT
PAIRING BUTTON