- ページ 8

浄水器 Atlantic Ultraviolet 10-0508BのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Atlantic Ultraviolet 10-0508B 20 ページ。 Germicidal ultraviolet water purifiers
Atlantic Ultraviolet 10-0508B にも：オーナーズマニュアル (16 ページ)

ページを印刷する

: MIN-6

NSTALLATION

SAFETY EQUIPMENT REQUIRED TO PERFORM TASK

Remove water purifier from shipping carton. Inspect water purifier, power cord and plug for damage. Do not operate if there

is any damage to the purifier, power cord or plug. All models, of the MINIPURE

the lamps packed separately. Keep the lamp aside for installation once the purifier has been properly installed.

2. Units occasionally experience damage in shipment due to the fragility of the quartz sleeve. It is therefore recommended to

inspect the water purifier for damage to the quartz sleeve after it has been removed from the shipping carton. Each end of the

unit as well as the inlet and outlet should be viewed to see if the quartz sleeve has experienced damage. If the quartz sleeve

shows signs of damage it should be replaced before the purifier is pressurized. See "Quartz Sleeve Installation, Cleaning

or Replacement" in the "Maintenance" section for the proper method of replacing the quartz sleeve in your water purifier.

The water purifier should be mounted horizontally on a flat dry surface. The purifier should not be solely supported by its

plumbing connections. Securing the water purifier using the optional wall bracket kit is recommended.

4. The water purifier must be connected to the cold water line only. Inlet water temperature should not exceed 100

It is recommended that a 5-micron sediment filter be installed, in line, prior to the water purifier. The sediment filter will

stop or trap large particulates from entering the water purifier. Particulates may cause damage to the quartz sleeve, as well as

interfere with the purifier's ability to disinfect the water. The sediment filter may also help to reduce the amount of routine

cleanings of the quartz sleeve.

6. Shut off valves should be installed on both the inlet and outlet sides of the water purifier. The use of bypass valves is not

recommended. The shut off valves allow the purifier to be isolated from the water supply, which is required when removing

the quartz sleeve.

7. Unions should be installed on both the inlet and outlet of the water purifier; this will allow easy removal of the water purifier

from the plumbing, if required. Apply Teflon

When all plumbing connections are complete, allow water to enter the water purifier at a low flow rate, until the purifier is

full. NOTE: Close the purifier outlet valve to pressurize the chamber. With the purifier pressurized, it should be checked

for leaks. Once it is determined that there are no leaks, the inlet valve can be fully opened.

Unpack the lamp and ballast. While holding lamp end, carefully push lamp socket on. Carefully slide lamp straight into the

quartz sleeve, without angling. Push the end cap on, over the static gland nut. Attach the ground connector to the grounding

stud of the chamber, with included hardware (see steps 14, 15, and 16 on Page 10)

WARNING: To insure proper operation and safety of your water purifier, your unit must be grounded

to a known good ground.

CAUTION: Lamp and quartz sleeve are easily damaged. Exercise care when handling.

10. Plug ballast into an approved Ground Fault Circuit Interrupt (GFCI) receptacle. Where a 2-prong or unprotected 3-prong

receptacle is encountered, it must be replaced by a properly grounded Ground Fault Circuit Interrupt (GFCI) receptacle.

Installation must be in accordance with the National Electrical Code and any local codes and ordinances by a qualified

Electrician. (Continued on Page 9)

MIN-9 120

50/60H

AND

tape to threads of inlet and outlet ports to ensure a tight seal.

Figure 4 - 120v 50/60Hz (ballast no. 10-0508B)

Z USING BALLAST NO

line of water purifiers, are shipped with

.10-0508B