- ページ 8

セキュリティシステム DSC SCW9045-868のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。DSC SCW9045-868 20 ページ。 Self contained wireless
DSC SCW9045-868 にも：ユーザーマニュアル (20 ページ)

ページを印刷する

Remote Arming and Disarming

The system can be armed and/or disarmed using the remote control device (wireless key). When arming

the system by using the Arm button on the wireless key, the system will acknowledge the command by

sounding a single bell squawk (if bell squawk is enabled) and when disarming using the Disarm button

on the wireless key the system will acknowledge the command by sounding two bell squawks (if bell

squawk is enabled). Three squawk pairs heard when disarming with the disarm button indicates that

that an alarm occurred while the system was armed. If you are unsure of the cause of the alarm, pro-

ceed with caution.

Emergency Keys

Press the

(

keypad sounder will beep indicating that the alarm input has been accepted and transmission to the

central station is underway. The

setup.

NOTE: The Fire keys can be disabled by the installer.

When Alarm Sounds

The system can generate 2 different alarm sounds:

• Continuous Siren = Intrusion (Burglary Alarm)

• Temporal / Pulsed Siren = Fire Alarm

Intrusion (Burglary) Alarm Continuous Siren

NOTE: If you are unsure of the source of the alarm, proceed with caution! If the alarm was acci-

dental, enter your Access Code to silence the alarm. If the alarm system is disarmed within the pro-

grammed Abort Window (check with the installer if this option has been enabled on your system

and what is the transmitter delay time programmed), no alarm transmission to the Central Station

will occur. Starting at the end of the Abort Window there is a five minute Cancel window, during

which a user can cancel, by entering his access code, an alarm that has been previously transmitted.

A cancel signal will be transmitted to the Central Station and the alarm system will also annunciate

that the cancel signal was transmitted. Call your central station to avoid a dispatch.

Fire Alarm Pulsed Siren

Follow your emergency evacuation plan immediately!

If the fire alarm was accidental (i.e. burned toast, bathroom steam, etc.), enter your Access Code to

silence the alarm. Call your central station to avoid a dispatch.

Time & Date Programming

Press

plus your Master Access Code to enter User Functions. Use the

the menu option then press

date (MM:DD:YY). Press

within the trouble menu (

ble Conditions on page 6),

NOTE: Your installer may have programmed your system to display the time and date while the key-

pad is idle. Press the

Bypassing Zones

Use the zone bypassing feature when you need access to a protected area while the system is armed,

or when a zone is temporarily out of service, but you need to arm the system. Bypassed zones will

not be able to sound an alarm. Bypassing zones reduces the level of security. If you are bypassing a

zone because it is not working, call a service technician immediately so that the problem can be

resolved and your system returned to proper working order. Ensure that no zones are unintentionally

bypassed when arming your system. Zones cannot be bypassed once the system is armed. Bypassed

zones are automatically cancelled each time the system is disarmed and must be bypassed again, if

required, before the next arming.

NOTE: 24-hour zones can only be unbypassed manually.

(

) or

(

) key for 2 seconds to generate a Fire, Auxiliary or Panic alarm. The

(

) key may or may not sound the bell depending on Installer

to select it. Enter the time in 24-hr. format (HH:MM), followed by the

to exit programming. If you are viewing a 'Loss of Clock', trouble from

), press

key to clear the date and time display if desired.

to directly enter Date and Time programming. See Trou-

scroll keys to find