産業機器 CaseLife Annealing CL1-V1.1のPDF マニュアルをオンラインで閲覧またはダウンロードできます。CaseLife Annealing CL1-V1.1 4 ページ。 Annealing machine

TURNING OFF AND STORAGE

1. Remove the cylinder from the torch/hose when not in use. Never store the torch attached to a fuel tank.

2. Turn the valves off. Note: The flame may to continue to burn for a short period of time if the torch has been operated in

an inverted (upside down) position.

3. When the torch has cooled down, turn the gas cylinder counter-clockwise from valve body to disconnect. Then, store the

torch and cylinder separately. Observe precautions on the cylinder label.

GENERAL SAFETY RULES

1. Do not use the torch until you have read and understood all the instructions, precautions and you have familiarized

yourself with the torch. Review instructions and precautions periodically to retain awareness. Deviating from these

procedures may result in fire, explosion, property damage and/or operator injury. Do not try to operate before reading

instructions.

2. Do not point torch towards face, other persons or flammable objects. Never attempt to use the torch as a cigarette

lighter.

3. Disconnect cylinder when not in use.

4. Never attempt to modify the torch construction and never use unapproved fuel.

5. Treat the torch as you would treat any fine tool or instrument, do not drop or otherwise abuse.

CaseLife Annealing

6. Do not use a leaking, damaged or malfunctioning torch. Stop using it immediately, DO NOT use the torch until you have

corrected the problem. Torches improperly operated, maintained or repaired can be dangerous. Improper use, service

repair or modification of the torch could result in damage to the product, property damage or personal injury to the

operator.

Brass Case Annealing

7. Work only in well ventilated areas.

8. Always place your work on a firebrick or fire resistant surface. If you are not sure if it's a firebrick or fire resistant surface,

CL1-V1.0 / CL1-V1.1

do not use it. Ordinary bricks and concrete can explode when subjected to high temperatures. Do not work on wood or

metal surfaces. Always shield your work.

9. Always wear protective gloves, eye-wear and use proper tools to handle hot work.

10. Be aware that the tip of the torch can get extremely hot during use. Take precautions to protect yourself and others

from accidental burns. Never use the torch on or near combustibles. Be especially careful around motor vehicles or ant

gasoline-fired products and beware of hidden fuel lines and tanks.

11. Always make certain the torch is placed on a level surface when connected to a gas cylinder to reduce the risk of

accidental tip – over. Make sure the torch is not pointed at a direction which could cause nearby objects to ignite when

torch is set down.

12. When thawing pipes, be very careful not to overheat surrounding materials.

13. Always have a fire extinguisher and a bucket of water near the torch and work area. Do not place them in the flame path

Welcome to your CaseLife Annealing Machine.

or in a location where you could not reach them should a fire break out.

14. Do not put your fingers in the loading wheel grooves during operation.

I'm sure you'll have loads of fun setup up and playing with your new toy but before you get started

15. Do not handle hot annealed brass cases, allow time for them to cool.

16. Do not handle the flame torch during or just after usage, allow time for cooling.

please read our manual and safety instructions.

17. Do not place hands in front of the torch flame during operation.

18. Wear appropriate footwear when lifting the annealing machine or gas cylinder.

It will help answer a few questions but should you need to ask something we've missed, please don't

WARNING

hesitate to contact us via our online form.

(Extremely flammable contents under pressure) Keep out of reach of children. Keep away from heat or flame. It is illegal and

dangerous to refill the cylinder. Obtain new gas cylinder from your dealer. Avoid prolonged exposure to sunlight. Do not

I'm sure your itching to get start so I'll wish you happy annealing.

store near heat or in a room used for habitation. Always close torch and hose valves and wait at least 30 seconds before

removing torch/hose from gas cylinder. Always detach gas cylinder from torch/hose when not in use. Do not breathe gas,

fumes, vapour or spray. If inhaled, remove affected person to fresh air. When gas cylinder is empty, discard in a safe place.

Do not throw on fire. Do not puncture or incinerate container.