ページを印刷するStopwatch Mode
The stopwatch measures elapsed time in units of 1/100 second up to 59 minutes, 59.99 seconds (60 minutes). When the maximum limit is
reached, the elapsed time automatically returns to zero and timing continues from there.
Performing Stopwatch Operations
Timekeeping Mode
Mode Indicator
(Three times)
About two
seconds
A Button
A
A
A
A
Seconds
• Split/Reset
• Press during elapsed time
measurement to display the
split time.
• Press when elapsed time
measurement is stopped to
reset the stopwatch to all
zeros.
1/100 second
Minutes
D
D Button
D
D
D
Current Time (24-hour format)
• Start/Stop
• Each press starts and stops
elapsed time measurement.
❚ To configure time and date settings
manually
1.
Timekeeping Mode
In the Timekeeping Mode,
hold down the A
A
A
A button
A
for about two seconds.
• This will cause the watch to
beep and display the
transmitter selection mode
setting screen.
A
A
A Button
A
A
• Displays the setting screen.
• Changes from the first
setting group to the next.
• Exits the setting screen.
B Button
B
B
B
B
• Scrolls back through the
options at the flashing
FREQUENCY (Frequency)
(selected) setting.
C
C
C
C Button
C
• Moves the flashing
between settings.
D
D
D
D
D Button
• Scrolls forward through the
options at the flashing
(selected) setting.
Operation Guide 2696/2832 ( B )
❚ Elapsed Time Measurement
Start
Stop
Reset
Pressing the A button while timing is stopped resets the
stopwatch to all zeros.
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting it
to all zeros causes the elapsed time measurement to resume from
where it was last stopped.
❚ Split Time Measurement
Start
Record split Release split
Stop
Reset
Pressing the A button while timing is being performed freezes the
current elapsed time on the display, but timing of the next split
continues internally.
• Changing to another mode while a split time is displayed cancels
the split time operation.
❚ 1st and 2nd Place Finishers
Start
1st finish
2nd finish
Displays time
Reset
(Displays time
of 2nd finish.
of 1st finish.)
2.
Press the A
A
A
A
A button to
advance to the next group
of settings.
• This causes the 12/24-hour
timekeeping setting to flash.
Example: 12H (12-hour
timekeeping)
3.
Use the C
C
C
C
C button so the
setting you want to change
is flashing on the display.
• Use the C button to cycle
through the time and date
settings shown below. Each
press of C causes the
applicable setting to flash.
12/24-hour
Seconds
Hour
Minute
timekeeping
Power Saving
Day
Month
Year
4.
While the 12/24-hour
timekeeping setting is
flashing, press the D
D
D
D
D
button to select the
setting you want.
• Pressing the D button toggles
the timekeeping format between
12-hour ("12H" indicator) and
24-hour ("24H" indicator).
Configuring Time and Date Settings Manually
Normally, you should never need to configure time and date settings manually if you have auto receive turned on and you are within the
range of a time calibration signal. If the watch is unable to update its settings automatically for some reason, however, you can configure
them manually as described below.
Time and Date Settings
Timekeeping Mode
(Hold down about two seconds.)
Transmitter
Home City Code
Selection Mode
Auto Receive
Summer Time
12/24-hour
Seconds
Hour
Minute
timekeeping
Power Saving
Day
Month
Year
• While the setting screen (the one with a flashing setting) is on the
display, use the C and A buttons to move the flashing between
settings.
5.
To restart the seconds
count to 00, press the D
D
D
D
D
button.
• Pressing the D button while
the seconds count is in the
range of 30 to 59 resets it to
Resets to 00.
00 and also adds 1 to the
minutes. Pressing the D
button in the range of 00 to 29
resets the seconds count
without changing the minutes.
6.
While the hour, minutes,
year, month, or day setting
is flashing, use the D
D
D
D
D (+)
and B
B (–) buttons to
B
B
B
change the setting.
• Holding down either button changes the setting at high speed.
• When setting the hour, make sure you specify AM (A) or PM
(P) correctly, or that you specify the correct 24-hour time.
• You can set a date in the range of January 1, 2000 to
December 31, 2099.
• The day of the week is set automatically in accordance with
the date you set.
A
A
A Button
A
A
• Displays the setting screen.
• Changes from the first setting
group to the next.
• Exits the setting screen.
C
C
C Button
C
C
• Moves the flashing between
settings.
See "Signal Reception Settings" for information about
calibration signal, Home City, summer time, and auto receive
settings.
7.
While the Power Saving
setting is flashing, press
D
D
the D
D button to toggle it
D
on (PS On) or off (PS OF).
Use the C button to select each of the settings and the D
and B buttons to change them.
8.
When the settings are the
way you want, press the
(Back)
A
A
A button.
A
A
• This exits the setting screen.
(Forward)
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
• The watch automatically makes adjustments for leap years
and month lengths.
8