- ページ 9

アンプ Audiotec Fischer Match PP 86DSPのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Audiotec Fischer Match PP 86DSP 15 ページ。 8-chanell amplifier with integrated 9-chanell dsp

ページを印刷する

Installation

format with a sample rate between 12 kHz and

96 kHz and no Dolby-coded signals.

5. Connection to power supply

Make sure to disconnect the battery before

installing the MATCH PP 86DSP!

The power supply of the PP 86DSP never ever

occurs via the MATCH cable harness. Always

directly connect the massive screw terminals of

the power leads of the car radio itself! Though

the PP 86DSP only has a limited average pow-

er consumption, it may draw very high currents

(up to 50 A) for the fraction of a second due to

its dynamically controlled internal power supply.

Important: You may risk a severe damage of

ic components inside your vehicle or even a

the power supply of the PP 86DSP!

Connect the +12 V power cable to the positive

terminal of the battery. The positive wire from

needs to have an inline fuse (50 A) at a distance

of less than 12 inches (30 cm) from the battery.

If your power wires are short (less than 1 m /

40") then a wire gauge of 6 mm² / AWG 10 will

The ground cable (same gauge as the +12 V

wire) should be connected to a common ground

reference point (this is located where the neg-

ative terminal of the battery is grounded to the

metal body of the vehicle) or to a prepared met-

al location on the vehicle chassis, i.e. an area

which has been cleaned of all paint residues.

6. Connecting the remote input

The remote input has to be connected to the ra-

is solely used as signal input. We do not recom-

mend controlling the remote input via the igni-

tion switch to avoid pop noise during turn on/off.

If the highlevel inputs of the System Connector

or the Highlevel Input E + F are used this input

does not need to be connected as long as the

car radio has BTL output stages.

The PP 86DSP will be turned on automatically

if the highlevel inputs of the System Connector

or the Highlevel Input E + F are used or if a sig-

nal is applied to the remote input terminal. The

Auto Remote switch (page 18, item 12) allows

to deactivate the automatic turn-on feature. The

feature should be deactivated if there are e.g.

Note: If the automatic turn-on function is deac-

tivated it is mandatory to use the remote input

signal of the System Connector and High-

level Input E + F will be ignored in this case.

To deactivate the automatic turn-on feature you

have to change the position of the Auto Remote

switch to "Off".

conducted with the DSP PC-Tool software

Ignoring this advice may result in damaging the

the PP 86DSP will be used to drive fully active

speaker systems, a wrong setup can destroy

your tweeters right away.

Information about connecting the PP 86DSP to

a computer can be found on page 25.

9. Connecting the loudspeaker outputs E - H

The loudspeaker outputs allow to connect a

passive Plug & Play subwoofer like the MATCH

PP 10E-D or further loudspeakers (e.g. cen-

ter speaker etc.). For the connection of a

Plug & Play subwoofer you have to connect the

8-pole Molex connector of the connection ca-

ble which is delivered with the subwoofer to the

Speaker Output E - H.

Optical Input

Afterwards the appropriate subwoofer has to be

activated in the DCM menu of the DSP PC-Tool

software.

Note:

nels for driving the subwoofer.

Alternatively the loudspeaker outputs can be

connected directly to the wires of further loud-

speakers by using the 8-pole connection cable

which is included in delivery. Never connect

any of the loudspeaker cables with the chassis