- ページ 4

掃除機 Dustless 16010のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Dustless 16010 9 ページ。 16 gallon wet/dry vacuum hepa vacuum, and toolsync tool activated vacuum

ページを印刷する

Extension cord instructions:

Use an outdoor, grounding type SJT

extension cord of 16 gauge (up to 35

feet ) or 14 gauge ( any length ). The

extension cord must employ a 3-prong

grounding type plug and a 3-pole recep-

tacle that accepts the machine plug.

Filters

Do not operate cleaner without filters

in place. To assure that your cleaner

operates at peak performance, it is

imperative that you use only genuine

Dustless Technologies filters.

Regular Wet/Dry Vacuum Filters:

Primary and secondary filters should be

held in place by their respective band

clamps. There should not be any puckers

or wrinkles that will allow dust to travel

through or suction will be reduced.

Micro Prefilter - Part #13141 is provided

with each vacuum. Packages of 2 are

available to purchase.

HEP Filters:

It is recommended to use part #13141 -

micro prefilter with your vacuum. Micro

Prefilters #13141 are available. They are

recommended to be used on any fine

dust application such as sanding drywall.

This is a disposable bag and should be

thrown away when full.

How to Clean Filters:

Special note for HEP filters: ll HEP

filters should be discarded after use, no

attempt to clean filters should be made.

Turn the unit off then remove the brass

agitator rod cover from the top of the

cleaner lid. The agitator rod will be

exposed. Lift the agitator rod about 1/2

inch and rock from side to side. The lid

acts as a pivot point for the filter support

basket, located underneath the lid. The

rocking motion of the basket agitates the

primary filter to knock off the layer of

dust that has accumulated. This will

make the suction resume. fter a period

of time, when suction is reduced and

cleaning the filters with the agitator rod

is not sufficient, the filters may be

replaced or laundered and reused.

Micro Prefilters are disposable and will

hold 20-30 lbs. of dust.

HOW TO USE

How to Replace Filters:

Regular Wet/ ry Vacuum Filter

assembly:

Turn vacuum lid upside down on a flat

surface. Place the small, white

secondary filter over the

spring mounted cage on

the underneath side of

the lid. Gently push the

filter all the way on and

compress the springs,

then let off all pressure

allowing the cage to push

the filter back out into a

relaxed position. Secure

filter firmly with the 7''

band clamp to the lid so

particles are not allowed

to go through to the

motor. Use a flat blade

screwdriver for this clamp.

Take the filter support basket with

agitator rod and turn it upside down.

Put the agitator rod through the hole in

the lid. The filter support basket rests

on top of the secondary filter with the

agitator rod through the lid hole.

Place the primary filter over the filter

support basket and secondary filter.

The side seam of the larger primary filter

should line up with the filter support

basket agitator rod and the filter is then

put around the large lip on the under-

neath side of the lid and secured into

place smoothly with the 10'' band clamp.

There should not be any wrinkles in the

fabric as they will affect the functioning

of the filters. The filter support basket is

suspended between the two filters and

the agitator rod extends through the top

of the lid. Use a flat blade screwdriver

for this clamp.

Turn right side up and screw the brass

agitator rod cover into the top of the

lid - only finger tight!! Do not

over tighten.

HEP Wet/Dry Vacuum

Filter assembly:

The HEP Filter is placed

over the crosspiece stud.

The threads will protrude

through the hole in the

middle of the HEP filter.

Slide the provided rubber

washer (part #91522) over

the threads of the stud

with the rubber side

against the HEP Filter.

Screw down the wing nut

(part #91523) and slightly

compress the rubber washer. It will

compress about 1/2 of its original

thickness. Next place the HEP Filter

Cover Support on top of the HEP filter

and finally place the HEP Filter Cover

over the filter and cover. ttach the filter

cover with the 10" band clamp using a

flat blade screwdriver.

Turn right side up and screw the brass

agitator rod cover into the top of the

lid - only finger tight!! Do not over

tighten. This part must be in place to

maintain suction.

Dry Pickup:

Wet waste should be emptied from tank

but filters can remain in place.

Connect suction hose and appropriate

attachments for use. s suction is

reduced from fine material coating the

filters, shut off the unit to clean filters.

Remove the brass agitator rod cover and

rock the agitator rod from side to side to

clean filters and resume suction.

fter Dry Pickup:

Disconnect cleaner from electrical outlet.

Release lid latches and remove cleaner

lid assembly as well as intermediate

cover from tank. Empty dry material from

the tank and intermediate cover.

To avoid back strain, do not lift a full

tank. First, scoop out enough debris to

make tank easier to lift.

Empty contents into a suitable receptacle.