Dustless 16010 Instrukcja obsługi - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odkurzacz Dustless 16010. Dustless 16010 9 stron. 16 gallon wet/dry vacuum hepa vacuum, and toolsync tool activated vacuum
Drukuj stronęExtension cord instructions:
Use an outdoor, grounding type SJT
extension cord of 16 gauge (up to 35
feet ) or 14 gauge ( any length ). The
extension cord must employ a 3-prong
grounding type plug and a 3-pole recep-
tacle that accepts the machine plug.
Filters
Do not operate cleaner without filters
in place. To assure that your cleaner
operates at peak performance, it is
imperative that you use only genuine
Dustless Technologies filters.
Regular Wet/Dry Vacuum Filters:
Primary and secondary filters should be
held in place by their respective band
clamps. There should not be any puckers
or wrinkles that will allow dust to travel
through or suction will be reduced.
Micro Prefilter - Part #13141 is provided
with each vacuum. Packages of 2 are
available to purchase.
HEP Filters:
It is recommended to use part #13141 -
micro prefilter with your vacuum. Micro
Prefilters #13141 are available. They are
recommended to be used on any fine
dust application such as sanding drywall.
This is a disposable bag and should be
thrown away when full.
How to Clean Filters:
Special note for HEP filters: ll HEP
filters should be discarded after use, no
attempt to clean filters should be made.
Turn the unit off then remove the brass
agitator rod cover from the top of the
cleaner lid. The agitator rod will be
exposed. Lift the agitator rod about 1/2
inch and rock from side to side. The lid
acts as a pivot point for the filter support
basket, located underneath the lid. The
rocking motion of the basket agitates the
primary filter to knock off the layer of
dust that has accumulated. This will
make the suction resume. fter a period
of time, when suction is reduced and
cleaning the filters with the agitator rod
is not sufficient, the filters may be
replaced or laundered and reused.
Micro Prefilters are disposable and will
hold 20-30 lbs. of dust.
4
HOW TO USE
How to Replace Filters:
Regular Wet/ ry Vacuum Filter
assembly:
Turn vacuum lid upside down on a flat
surface. Place the small, white
secondary filter over the
spring mounted cage on
the underneath side of
the lid. Gently push the
filter all the way on and
compress the springs,
then let off all pressure
allowing the cage to push
the filter back out into a
relaxed position. Secure
filter firmly with the 7''
band clamp to the lid so
particles are not allowed
to go through to the
motor. Use a flat blade
screwdriver for this clamp.
Take the filter support basket with
agitator rod and turn it upside down.
Put the agitator rod through the hole in
the lid. The filter support basket rests
on top of the secondary filter with the
agitator rod through the lid hole.
Place the primary filter over the filter
support basket and secondary filter.
The side seam of the larger primary filter
should line up with the filter support
basket agitator rod and the filter is then
put around the large lip on the under-
neath side of the lid and secured into
place smoothly with the 10'' band clamp.
There should not be any wrinkles in the
fabric as they will affect the functioning
of the filters. The filter support basket is
suspended between the two filters and
the agitator rod extends through the top
of the lid. Use a flat blade screwdriver
for this clamp.
Turn right side up and screw the brass
agitator rod cover into the top of the
lid - only finger tight!! Do not
over tighten.
HEP Wet/Dry Vacuum
Filter assembly:
The HEP Filter is placed
over the crosspiece stud.
The threads will protrude
through the hole in the
middle of the HEP filter.
Slide the provided rubber
washer (part #91522) over
the threads of the stud
with the rubber side
against the HEP Filter.
Screw down the wing nut
(part #91523) and slightly
compress the rubber washer. It will
compress about 1/2 of its original
thickness. Next place the HEP Filter
Cover Support on top of the HEP filter
and finally place the HEP Filter Cover
over the filter and cover. ttach the filter
cover with the 10" band clamp using a
flat blade screwdriver.
Turn right side up and screw the brass
agitator rod cover into the top of the
lid - only finger tight!! Do not over
tighten. This part must be in place to
maintain suction.
Dry Pickup:
Wet waste should be emptied from tank
but filters can remain in place.
Connect suction hose and appropriate
attachments for use. s suction is
reduced from fine material coating the
filters, shut off the unit to clean filters.
Remove the brass agitator rod cover and
rock the agitator rod from side to side to
clean filters and resume suction.
fter Dry Pickup:
Disconnect cleaner from electrical outlet.
Release lid latches and remove cleaner
lid assembly as well as intermediate
cover from tank. Empty dry material from
the tank and intermediate cover.
To avoid back strain, do not lift a full
tank. First, scoop out enough debris to
make tank easier to lift.
Empty contents into a suitable receptacle.