ロックス Austral Lock S14RのPDF 図解取り付け説明書をオンラインで閲覧またはダウンロードできます。Austral Lock S14R 2 ページ。 Multi-point rod kit for sliding security doors

ページを印刷する

S14R

multi-point rod kit

for sliding security doors

Austral

Illustrated fitting instructions

Lock

ILLUSTRATED FITTING INSTRUCTIONS

Prepare Door

Prepare the door according to the table and diagram

below, to suit the application.

Code

[A]

[B]

High

S14R/H

546 mm

961 mm

Low

S14R/L

961 mm

546 mm

Suit 1500

S14R/P

375 mm

961 mm

Sample

S14R/S

375 mm

367mm

[A]

172

156

Centre Line

of Cutout

[B]

16 Slot Width

(OPTIONAL)

Adjustable Rod Setup

Follow this step if using Adjustable Rods, otherwise

go to Step 3.

Mark the cutout dimensions A and B on the

Measurement Guide provided.

NOTE: The standard cutout positions are pre-marked.

If you are fitting several doors with the same cutout

dimensions, it is recommended that you securely tape

the Measurement Guide to a benchtop or piece of

timber. Then drill holes (4.5mm diameter) to locate and

secure the rod ends while fastening.

central hole

(large hole upwards)

coupling

rod

min. 100

rod length

Insert the steel rods into the brass coupling as shown.

The coupling should be placed in the center between

the two rod ends, and have the larger central hole

facing upwards.

NOTE: If the distance between the straight rod ends and

the bent rod ends is less than 100mm (as shown above)

you must cut-down the rods enough to provide this

clearance.

The rod ends must be pointing downwards into the

benchtop. If you are not drilling holes for the rod ends,

you will need to place a flat block (10mm thick) under

the coupling.

drive pin

rolled pin

central hole

coupling

drive

rolled

Insert the rolled steel pin into the large central hole and

tap with hammer until it is fully inside the coupling.

CHECK THAT THE ROD ENDS ARE PARALLEL AND

POINTING STRAIGHT DOWN.

Re-align if necessary and check the overall length.

Place the pointed end of the drive pin into the top of the

rolled pin and hammer until it is fully inside the coupling.

drive pin and rolled pin

flush inside the coupling

coupling

The Adjustable Rod is now ready for installation.

Install Remote Locks

Rod lengths for each application are given in the table

below for reference. If using the Adjustable Rod system,

see over page for setup instructions.

Fit a supplied o-ring on each rod 60 - 80mm from the

remote end (not needed for Adjustable Rods).

Assemble corresponding rods to the top and bottom

remote locks, ensuring the UP arrows on the remote

locks are pointing towards the top of the door.

With the top remote lock connected to the top rod,

slide the free-end of the top rod though the top

remote lock cutout.

Repeat the above process for the bottom remote lock.

NOTE: DO NOT SCREW THE REMOTE LOCKS IN YET.

top

remote lock

TOP Rod

BOT. Rod

High

570 mm

993 mm

Low

985 mm

578 mm

Suit 1500

399 mm

993 mm

Sample

399 mm

o-ring

Formula

=[A]+24

=[B]+32

rod

free-ends

top

remote lock

top cutout

o-ring

bottom

remote lock

bottom

bottom cutout

remote lock

Remove Plug in Centrelock

Remove

Ø5mm

plug in the drive tab on the rear of the

centrelock and discard.

drive tab

REMOVE

Ø5mm plug

Install Centrelock

Pull the free-ends of the rods out through the centrelock

cutout.

Insert the rod free-ends into the two Ø5 drive holes

on the rear of the centrelock.

Insert the centrelock into the centrelock cutout and

secure with two #8x13mm lock body screws.

centrelock

cutout

PLEASE TURN PAGE FOR STEPS 6 - 11

(PK0190) S14R Instructions A4 R13.cdr

lock body

screw

rod

free-end