Austral Lock S14R Geïllustreerde montage-instructies

Blader online of download pdf Geïllustreerde montage-instructies voor {categorie_naam} Austral Lock S14R. Austral Lock S14R 2 pagina's. Multi-point rod kit for sliding security doors

Pagina afdrukken
S14R
multi-point rod kit
for sliding security doors
Austral
Illustrated fitting instructions
Lock
ILLUSTRATED FITTING INSTRUCTIONS
1.
Prepare Door
Prepare the door according to the table and diagram
below, to suit the application.
Code
[A]
[B]
High
S14R/H
546 mm
961 mm
Low
S14R/L
961 mm
546 mm
Suit 1500
S14R/P
375 mm
961 mm
Sample
S14R/S
375 mm
367mm
64
[A]
25
60
172
156
Centre Line
of Cutout
60
19
[B]
19
64
16 Slot Width
2.
(OPTIONAL)
Adjustable Rod Setup
Follow this step if using Adjustable Rods, otherwise
go to Step 3.
Mark the cutout dimensions A and B on the
Measurement Guide provided.
NOTE: The standard cutout positions are pre-marked.
If you are fitting several doors with the same cutout
dimensions, it is recommended that you securely tape
the Measurement Guide to a benchtop or piece of
timber. Then drill holes (4.5mm diameter) to locate and
secure the rod ends while fastening.
central hole
(large hole upwards)
coupling
rod
rod
min. 100
min. 100
rod length
Insert the steel rods into the brass coupling as shown.
The coupling should be placed in the center between
the two rod ends, and have the larger central hole
facing upwards.
NOTE: If the distance between the straight rod ends and
the bent rod ends is less than 100mm (as shown above)
you must cut-down the rods enough to provide this
clearance.
The rod ends must be pointing downwards into the
benchtop. If you are not drilling holes for the rod ends,
you will need to place a flat block (10mm thick) under
the coupling.
drive pin
rolled pin
central hole
coupling
drive
rolled
pin
pin
Insert the rolled steel pin into the large central hole and
tap with hammer until it is fully inside the coupling.
CHECK THAT THE ROD ENDS ARE PARALLEL AND
POINTING STRAIGHT DOWN.
Re-align if necessary and check the overall length.
Place the pointed end of the drive pin into the top of the
rolled pin and hammer until it is fully inside the coupling.
drive pin and rolled pin
flush inside the coupling
coupling
The Adjustable Rod is now ready for installation.
3.
Install Remote Locks
Rod lengths for each application are given in the table
below for reference. If using the Adjustable Rod system,
see over page for setup instructions.
Fit a supplied o-ring on each rod 60 - 80mm from the
remote end (not needed for Adjustable Rods).
Assemble corresponding rods to the top and bottom
remote locks, ensuring the UP arrows on the remote
locks are pointing towards the top of the door.
With the top remote lock connected to the top rod,
slide the free-end of the top rod though the top
remote lock cutout.
Repeat the above process for the bottom remote lock.
NOTE: DO NOT SCREW THE REMOTE LOCKS IN YET.
top
remote lock
TOP Rod
BOT. Rod
High
570 mm
993 mm
Low
985 mm
578 mm
Suit 1500
399 mm
993 mm
Sample
399 mm
399 mm
o-ring
Formula
=[A]+24
=[B]+32
mm
rod
free-ends
top
remote lock
top cutout
o-ring
bottom
remote lock
bottom
bottom cutout
remote lock
4.
Remove Plug in Centrelock
Remove
Ø5mm
plug in the drive tab on the rear of the
centrelock and discard.
drive tab
REMOVE
Ø5mm plug
5.
Install Centrelock
Pull the free-ends of the rods out through the centrelock
cutout.
Insert the rod free-ends into the two Ø5 drive holes
on the rear of the centrelock.
mm
Insert the centrelock into the centrelock cutout and
secure with two #8x13mm lock body screws.
centrelock
cutout
PLEASE TURN PAGE FOR STEPS 6 - 11
(PK0190) S14R Instructions A4 R13.cdr
lock body
screw
rod
free-end