- ページ 2

ドローン Gadgetree MINI DRONEのPDF 操作説明をオンラインで閲覧またはダウンロードできます。Gadgetree MINI DRONE 3 ページ。

ページを印刷する

MODE 2 (DEFAULT MODE)

Red light is on the right. Green light is on the left.

One key automatic return

Headless mode

Up/Down/Left/

Right/High/Low/

Speed lever

Left trimmer

Right trimmer

OPERATING INSTRUCTIONS

Hover up and down

Push the throttle lever up or down

Turn left and right

Push the left lever left or right

FINE TUNING

Forward/backward

Sideways

Use the backward/forward

Use the left/right sideways

trimmer to correct the Mini

fly trimmer to correct the

Drone if it keeps flying

Mini Drone if it keeps flying

forwards or backwards

left or right

LOW VOLTAGE PROTECTION

If the Mini Drone battery is low, the rotors will stop automatically in order to

protect the battery.

RESET FUNCTION

If the Mini Drone is flying erratically or not as expected simply restore

factory default settings as follows:

1. Turn the Mini Drone ON.

2. Turn the transmitter ON.

3. When the mini drone's LED stops flashing quickly and begins to flash

slowly push the throttle level up as far as it will go. LED will turn ON.

Forward trimmer

Backward trimmer

Forward/Backward/

Left/Right sideways/3D

Eversions

Right sideways fly

trimmer

Power/Charge

LED indicator

Left sideways fly

trimmer

Forward and backward

Push the direction lever up or down

Left and right sideways

Push the right lever left or right

Turning

Use the right/left trimmer to

correct the Mini Drone if it

keeps rotating

4. Place the Mini Drone on a level surface, then push the transmitter

levers to the down and right for 2-3 seconds. LED indicator will flash

quickly for 2-3 seconds then stop flashing and remain ON. The mini

drone has been successfully reset.

THROWING FLIGHT

Gently throw the Mini Drone up in the air, then push the throttle up the

Mini Drone will level out and hover automatically.

3D EVERSION

Once you are familiar with the Mini Drone's basic operation you can do

exciting tricks and stunts.

• Fly the Mini Drone to a height of at least 3 metres.

• Press the 3D eversion switch (right thumb stick mode 2) then push the

right rudder in any direction to perform a 360 degree flip.

TIP: 3D eversion requires full battery power to function properly

HEADLESS MODE

When syncing, the antenna of the transmitter must be aligned with the

back of the mini drone. When you press the headless mode button dur-

ing flight you will hear 3 beeps and the LED indicator will turn ON. While

in headless mode the transmitter must remain in front of the Mini Drone.

The Mini Drone will fly in the direction that the lever is pushed. To exit

headless mode, simply press the headless mode button again. You will

hear a beep indicating the headless mode has been turned OFF.

CAUTION

After fixing the Mini Drone must be reset

• Place the Mini Drone on a level surface, then

push the transmitter levers to the down and left

for 2-3 seconds. LED indicator will flash quickly

for 2-3 seconds then stop flashing and remain ON. The Mini Drone

has been successfully reset

ONE BUTTON AUTOMATIC RETURN

If the Mini Drone flies too far, simply call it back using the one button

automatic return function.

• The antenna of the transmitter must be aimed at the end of the Mini

Drone

• Press the one button automatic return button. You will hear a beep

and the Mini Drone will return to you. To cancel the automatic return,

simply press the direction lever

CAUTION: Automatic return can only be used if the transmitter is in the

same location it was when the Mini Drone took flight.

TROUBLESHOOTING

Problem

Reason

Low battery–

Mini Drone

Low battery–

No response from the

transmitter

mini drone

Incorrect frequency

Low battery–

transmitter

Slow to respond or

Interference from

difficult to manoeuver

another R/C vehicle

nearby

Solution

Charge the Mini

Drone

Replace batteries

Ensure Mini Drone

and transmitter are on

the same frequency

Replace batteries

Repair to pre-flight

state