Gadgetree MINI DRONE Instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Drony Gadgetree MINI DRONE. Gadgetree MINI DRONE 3 stron.
Drukuj stronęMODE 2 (DEFAULT MODE)
Red light is on the right. Green light is on the left.
One key automatic return
Headless mode
Up/Down/Left/
Right/High/Low/
Speed lever
Left trimmer
Right trimmer
OPERATING INSTRUCTIONS
Hover up and down
Push the throttle lever up or down
Turn left and right
Push the left lever left or right
FINE TUNING
Forward/backward
Sideways
Use the backward/forward
Use the left/right sideways
trimmer to correct the Mini
fly trimmer to correct the
Drone if it keeps flying
Mini Drone if it keeps flying
forwards or backwards
left or right
LOW VOLTAGE PROTECTION
If the Mini Drone battery is low, the rotors will stop automatically in order to
protect the battery.
RESET FUNCTION
If the Mini Drone is flying erratically or not as expected simply restore
factory default settings as follows:
1. Turn the Mini Drone ON.
2. Turn the transmitter ON.
3. When the mini drone's LED stops flashing quickly and begins to flash
slowly push the throttle level up as far as it will go. LED will turn ON.
Forward trimmer
Backward trimmer
Forward/Backward/
Left/Right sideways/3D
Eversions
Right sideways fly
trimmer
Power/Charge
LED indicator
Left sideways fly
trimmer
Forward and backward
Push the direction lever up or down
Left and right sideways
Push the right lever left or right
Turning
Use the right/left trimmer to
correct the Mini Drone if it
keeps rotating
4. Place the Mini Drone on a level surface, then push the transmitter
levers to the down and right for 2-3 seconds. LED indicator will flash
quickly for 2-3 seconds then stop flashing and remain ON. The mini
drone has been successfully reset.
THROWING FLIGHT
Gently throw the Mini Drone up in the air, then push the throttle up the
Mini Drone will level out and hover automatically.
3D EVERSION
Once you are familiar with the Mini Drone's basic operation you can do
exciting tricks and stunts.
• Fly the Mini Drone to a height of at least 3 metres.
• Press the 3D eversion switch (right thumb stick mode 2) then push the
right rudder in any direction to perform a 360 degree flip.
TIP: 3D eversion requires full battery power to function properly
HEADLESS MODE
When syncing, the antenna of the transmitter must be aligned with the
back of the mini drone. When you press the headless mode button dur-
ing flight you will hear 3 beeps and the LED indicator will turn ON. While
in headless mode the transmitter must remain in front of the Mini Drone.
The Mini Drone will fly in the direction that the lever is pushed. To exit
headless mode, simply press the headless mode button again. You will
hear a beep indicating the headless mode has been turned OFF.
CAUTION
After fixing the Mini Drone must be reset
• Place the Mini Drone on a level surface, then
push the transmitter levers to the down and left
for 2-3 seconds. LED indicator will flash quickly
for 2-3 seconds then stop flashing and remain ON. The Mini Drone
has been successfully reset
ONE BUTTON AUTOMATIC RETURN
If the Mini Drone flies too far, simply call it back using the one button
automatic return function.
• The antenna of the transmitter must be aimed at the end of the Mini
Drone
• Press the one button automatic return button. You will hear a beep
and the Mini Drone will return to you. To cancel the automatic return,
simply press the direction lever
CAUTION: Automatic return can only be used if the transmitter is in the
same location it was when the Mini Drone took flight.
TROUBLESHOOTING
Problem
Reason
Low battery–
Mini Drone
Low battery–
No response from the
transmitter
mini drone
Incorrect frequency
Low battery–
transmitter
Slow to respond or
Interference from
difficult to manoeuver
another R/C vehicle
nearby
Solution
Charge the Mini
Drone
Replace batteries
Ensure Mini Drone
and transmitter are on
the same frequency
Replace batteries
Repair to pre-flight
state