- ページ 8

ツール Gage Bilt GB585AのPDF オリジナル取扱説明書をオンラインで閲覧またはダウンロードできます。Gage Bilt GB585A 20 ページ。 Installation tool
Gage Bilt GB585A にも：インストール (11 ページ)

ページを印刷する

WARNING:

Only qualified and trained operators should install, adjust or use the assembly power tool for non-threaded

mechanical fasteners.

WARNING:

Operator

WARNING:

It is required that eye protection, hearing protection and safety boots be worn at all times while handling this

equipment.

WARNING:

The users or the user's employer should assess specific risks that could be present before each use based on

their application.

● Be sure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of

any moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.

●

Verify the air lines and/or hydraulic hoses are not a trip hazard.

●

Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool

●

Verify that hydraulic hose fittings and couplings, air and electrical connections are secure before each use.

WARNING:

Do not pull rivet in the air. Personal injury from fastener ejecting may occur.

WARNING:

Do not carry from hoses or use as a hammer.

WARNING:

Do not use in explosive atmosphere.

WARNING:

Ensure air hose is securely connected to avoid possible hose whipping.

WARNING:

Always disconnect air supply, where applicable, when tool is not in use to prevent accidental start-up.

WARNING:

Do not exceed the maximum relief-valve setting stated on the tool and manual.

WARNING:

Do not operate when recommended pressures are exceeded as it could cause severe personal injury and or

damage the equipment.

WARNING:

Use only Gage Bilt hydraulic hoses and couplings, or equivalent, rated for 10,000 psi. (689.5 bar) working pressure.

CAUTION:

Do not use beyond the design intent.

1. Set hydraulic power unit to the recommended pressure, 5,700 psi (393.0 bar) Max. for the pull and 2,400 psi (165.5 bar) Max. for the

return. Gage Bilt pressure gage assy (942280) (sold separately) is recommended to aid in this procedure. "See hydraulic power unit

manual for correct procedure when adjusting pressures".

Note:

Power units require a free flow of air for cooling purposes and should therefore be positioned in a well ventilated area

free from hazardous fumes.

2. Turn off the hydraulic power unit. Wipe all couplers clean before connecting. Failure to do so can result in damage to the couplers

and cause overheating. Connect hydraulic hoses then electric cord to power supply.

3. Turn hydraulic power unit on and cycle tool five times by depressing actuator to ensure piston is in the full forward position.

4. Disconnect electric cord / air line from power supply.

5. Attach nose assembly

5a. Screw collet assembly onto piston until top of

collet flat lines up with top of tool.

5b. If collet lock is not in piston groove, continue to turn

1/4 turn clockwise until ball lock engages in groove.

5c. Tighten set screw.

5d. Slide anvil over assembled collet. While pushing down on anvil,

install split ring, sleeve and retaining ring (furnished with tool).

(See proper data sheet for further instructions.)

6. Re-connect electric cord / air line into power supply.

Note: See GB7624 NOSE ASSEMBLY ATTACHMENT video as reference for

proper nose assembly attachment procedure located on our website, at :

http://www.gagebilt.com/rivet_tools_videos.php

GB585 / GB585A INTALLATION TOOL

HOW TO SET-UP THE GB585 / GB585A

MUST

read and understand all warnings and cautions.

5,700 psi

(393.0

bar)

Max.

2,400 psi

(165.5

bar)

Max.

REV. 12/17