- ページ 6

ツール Gage Bilt GB704SR-8のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Gage Bilt GB704SR-8 14 ページ。

DESCRIPTION

WARNING:

The balance of this tool is designed for vertical use and is not suited for any other applications. Gage

Bilt will be pleased to advise for your specific application.

The GB704SR-8 is a pneumatic-hydraulic split handle riveter designed specifically for the efficient installation of a wide

range of blind rivets. This tool's unique "split" system provides the operator with a lightweight ergonomic tool. The

handle assy and head cylinder assembly when held in hand weighs just 1.5 lbs (.68kg)! The entire split handle riveter

weighs 6.75 lbs. (3.06 kg). It has a .600 (15.24 mm) rivet setting stroke.

The GB704SR-8 split handle riveter operates with 90 to 100 psi (6.2-6.9 bar). providing maximum efficiency. At 90 psi.

(6.2 bar) air pressure, the GB704SR-8 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles per minute.

The GB704SR-8 comes with 8 feet of hose. Hoses are attached to the rear of the manifold-head assy. Vacuum systems

are available for this tool, please consult our engineering department for specific applications.

The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting.

MAINTENANCE

WARNING:

Maintenance personnel

WARNING:

Disconnect tool from its power source before performing maintenance.

WARNING:

Excessive contact with hydraulic oil and lubricants should be avoided.

WARNING:

Dispose of Hydraulic Oil in accordance with applicable regulations.

WARNING:

Read MSDS documents for all applicable materials.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for

service and care will extend the life of your tool.

*Only use an air supply set at 90-100 psi. (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.

*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent)

and free of air by using the air bleeder assy (704153) on a weekly basis.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable tool

manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride

on with light machine oil on a daily basis.

*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at

the end of each working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit GB740TK is recommended.

HYDRAULIC THREAD PREPARATION

IMPORTANT:

Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon® infused pipe

dope is recommended.

applied, pieces may enter the hydraulic system and cause malfunction and damage. Use 1 1/2 wraps

of tape on each thread. Cut off all loose tape ends. Tighten until fitting feels snug and then go 1/2 to a

full turn past that point.

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly

reduce downtime and increase life of components. Using

sewing machine oil, or an equivalent cleaner/lubricant, follow

instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3. Cycle tool 8-10 times and wipe dry.

TORQUE SPECIFICATIONS

Button Head Cap Screws (A-928) = 40 inch lbs.

Socket Head Cap Screws (400061 and 400066) = 40 inch lbs.

Packing Plug (744118) = 45 foot lbs

Flexlock Nut (400559) = 40 inch lbs.

End Cap (704112) = 45 foot lbs.

Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)

S/N: 1088 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

MUST

read and understand all warnings and cautions.

CAUTION:

Teflon tape is an excellent thread sealer, however, if not properly

CAUTION:

Over tightening can easily distort the threads.

Image may not reflect

actual tool.

11/11 Rev. 9/14