Gage Bilt GB704SR-8 Manual de instalação - Página 6
Procurar online ou descarregar pdf Manual de instalação para Ferramentas Gage Bilt GB704SR-8. Gage Bilt GB704SR-8 14 páginas.
Imprimir páginaDESCRIPTION
WARNING:
The balance of this tool is designed for vertical use and is not suited for any other applications. Gage
Bilt will be pleased to advise for your specific application.
The GB704SR-8 is a pneumatic-hydraulic split handle riveter designed specifically for the efficient installation of a wide
range of blind rivets. This tool's unique "split" system provides the operator with a lightweight ergonomic tool. The
handle assy and head cylinder assembly when held in hand weighs just 1.5 lbs (.68kg)! The entire split handle riveter
weighs 6.75 lbs. (3.06 kg). It has a .600 (15.24 mm) rivet setting stroke.
The GB704SR-8 split handle riveter operates with 90 to 100 psi (6.2-6.9 bar). providing maximum efficiency. At 90 psi.
(6.2 bar) air pressure, the GB704SR-8 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles per minute.
The GB704SR-8 comes with 8 feet of hose. Hoses are attached to the rear of the manifold-head assy. Vacuum systems
are available for this tool, please consult our engineering department for specific applications.
The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting.
MAINTENANCE
WARNING:
Maintenance personnel
WARNING:
Disconnect tool from its power source before performing maintenance.
WARNING:
Excessive contact with hydraulic oil and lubricants should be avoided.
WARNING:
Dispose of Hydraulic Oil in accordance with applicable regulations.
WARNING:
Read MSDS documents for all applicable materials.
The performance of any tool depends upon good maintenance practices. Following these minimal requirements for
service and care will extend the life of your tool.
*Only use an air supply set at 90-100 psi. (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.
*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent)
and free of air by using the air bleeder assy (704153) on a weekly basis.
*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable tool
manuals and nose assembly data sheets prior to operating tools.
*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride
on with light machine oil on a daily basis.
*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at
the end of each working shift to check that they are secure.
*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).
*For a complete overhaul, tool kit GB740TK is recommended.
HYDRAULIC THREAD PREPARATION
IMPORTANT:
Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon® infused pipe
dope is recommended.
applied, pieces may enter the hydraulic system and cause malfunction and damage. Use 1 1/2 wraps
of tape on each thread. Cut off all loose tape ends. Tighten until fitting feels snug and then go 1/2 to a
full turn past that point.
CLEANING AND LUBRICATING PROCEDURE
Daily cleaning and lubrication of nose assembly will greatly
reduce downtime and increase life of components. Using
sewing machine oil, or an equivalent cleaner/lubricant, follow
instructions below.
1. Disconnect tool vacuum line (if equipped).
2. Point nose assembly into oil as shown.
3. Cycle tool 8-10 times and wipe dry.
TORQUE SPECIFICATIONS
Button Head Cap Screws (A-928) = 40 inch lbs.
Socket Head Cap Screws (400061 and 400066) = 40 inch lbs.
Packing Plug (744118) = 45 foot lbs
Flexlock Nut (400559) = 40 inch lbs.
End Cap (704112) = 45 foot lbs.
Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)
S/N: 1088 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
MUST
read and understand all warnings and cautions.
CAUTION:
Teflon tape is an excellent thread sealer, however, if not properly
CAUTION:
Over tightening can easily distort the threads.
6
Image may not reflect
actual tool.
11/11 Rev. 9/14