- ページ 6

電動工具 Gage Bilt GB704のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Gage Bilt GB704 13 ページ。 Installation tool
Gage Bilt GB704 にも：マニュアル (14 ページ), オリジナル取扱説明書 (20 ページ)

ページを印刷する

DESCRIPTION

WARNING:

The balance of this tool is designed for horizontal use and is not ergonomically best

suited for all applications. Gage Bilt will be pleased to advise for your specific application.

The GB704 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind

rivets. It weighs 4.30 lbs. (1.95kg) and can be operated in any position with one hand. It has a .540" (13.72mm) rivet

setting stroke and a rated pull load of 3300 lbs (14.68 kN) with 90 psi (6.2 bar) air pressure at the air inlet.

The GB704 riveter is designed to operate on a range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the

maximum efficiency. At 90 psi (6.2 bar) air pressure, the GB704 does not exceed 81.5 dB (A) and consumes 3.9 cfm

at 20 cycles a minute.

The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.

NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. (See page 12 for

nose assembly recommendations.)

MAINTENANCE

WARNING:

Maintenance personnel

WARNING:

Disconnect tool from its power source before performing maintenance.

WARNING:

Excessive contact with hydraulic oil and lubricants should be avoided.

WARNING:

Dispose of Hydraulic Oil in accordance with applicable regulations.

WARNING:

Read MSDS documents for all applicable materials.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for

service and care will extend the life of your tool.

*Only use a clean dry air supply set at 90-100 p.s.i. (6.2-6.9 bar) Max. equipped with a filter-regulator to prevent wear.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all

applicable tool manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride

on with light machine oil on a daily basis.

*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at

the end of each working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit GB704TK is recommended (see page 8).

WEEKLY MAINTENANCE



Keep the hydraulic system full (only use Dexron III or equivalent) and free of air by using the air bleeder assy

(704153) on a weekly basis. or as needed. (See Filling and Bleeding).

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly reduce

downtime and increase life of components. Using sewing machine

oil, or an equivalent cleaner/lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown (Fig. A).

3. Cycle tool 8-10 times and wipe dry.

TORQUE SPECIFICATIONS

Button Head Cap Screws (A-928) = 40 inch lbs.

Flexlock Nut (400559) = 40 inch lbs.

Packing Plug (704118) = 45 foot lbs.

End Cap (704112) = 45 foot lbs.

Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)

GB704 S/N: 3213 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

MUST

SEE TROUBLESHOOTING AND OVERHAUL FOR FURTHER GUIDANCE.

read and understand all warnings and cautions.

Image may not reflect

actual tool.

Fig A.

6/11 Rev. 9/14