Gage Bilt GB704 Посібник з монтажу - Сторінка 6
Переглянути онлайн або завантажити pdf Посібник з монтажу для Електроінструмент Gage Bilt GB704. Gage Bilt GB704 13 сторінок. Installation tool
Також для Gage Bilt GB704: Посібник (14 сторінок), Оригінальна інструкція з експлуатації (20 сторінок)
Друкувати сторінку
DESCRIPTION
WARNING:
The balance of this tool is designed for horizontal use and is not ergonomically best
suited for all applications. Gage Bilt will be pleased to advise for your specific application.
The GB704 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind
rivets. It weighs 4.30 lbs. (1.95kg) and can be operated in any position with one hand. It has a .540" (13.72mm) rivet
setting stroke and a rated pull load of 3300 lbs (14.68 kN) with 90 psi (6.2 bar) air pressure at the air inlet.
The GB704 riveter is designed to operate on a range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the
maximum efficiency. At 90 psi (6.2 bar) air pressure, the GB704 does not exceed 81.5 dB (A) and consumes 3.9 cfm
at 20 cycles a minute.
The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. (See page 12 for
nose assembly recommendations.)
MAINTENANCE
WARNING:
Maintenance personnel
WARNING:
Disconnect tool from its power source before performing maintenance.
WARNING:
Excessive contact with hydraulic oil and lubricants should be avoided.
WARNING:
Dispose of Hydraulic Oil in accordance with applicable regulations.
WARNING:
Read MSDS documents for all applicable materials.
The performance of any tool depends upon good maintenance practices. Following these minimal requirements for
service and care will extend the life of your tool.
*Only use a clean dry air supply set at 90-100 p.s.i. (6.2-6.9 bar) Max. equipped with a filter-regulator to prevent wear.
*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all
applicable tool manuals and nose assembly data sheets prior to operating tools.
*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride
on with light machine oil on a daily basis.
*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at
the end of each working shift to check that they are secure.
*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).
*For a complete overhaul, tool kit GB704TK is recommended (see page 8).
WEEKLY MAINTENANCE
Keep the hydraulic system full (only use Dexron III or equivalent) and free of air by using the air bleeder assy
(704153) on a weekly basis. or as needed. (See Filling and Bleeding).
CLEANING AND LUBRICATING PROCEDURE
Daily cleaning and lubrication of nose assembly will greatly reduce
downtime and increase life of components. Using sewing machine
oil, or an equivalent cleaner/lubricant, follow instructions below.
1. Disconnect tool vacuum line (if equipped).
2. Point nose assembly into oil as shown (Fig. A).
3. Cycle tool 8-10 times and wipe dry.
TORQUE SPECIFICATIONS
Button Head Cap Screws (A-928) = 40 inch lbs.
Flexlock Nut (400559) = 40 inch lbs.
Packing Plug (704118) = 45 foot lbs.
End Cap (704112) = 45 foot lbs.
Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)
GB704 S/N: 3213 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
MUST
SEE TROUBLESHOOTING AND OVERHAUL FOR FURTHER GUIDANCE.
read and understand all warnings and cautions.
6
Image may not reflect
actual tool.
Fig A.
6/11 Rev. 9/14