- ページ 3

配管製品 Dawn AACT302134-01のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Dawn AACT302134-01 5 ページ。 Vanity

Safety Glasses, Pencil, Level, Tape Measure, Stud Finder, Assorted Screwdrivers, Assorted Wrenches,

Drill, Screw Gun, Caulking Gun, Hammer, Screws, Nail Anchors/Molly Screws

Comply with Plumbing Codes

●

Before installing any Dawn product in your new or remodeled kitchen, you should make sure that you are in compliance with all

local plumbing codes.

Check Product Condi on

●

Before installa on, please check the condi on of the product and, if appropriate, its components. If there is any problem with

the product and/or its components, please contact the store you purchased it from for a replacement. As soon as you have in-

spected your product, please return it to its original packaging un l you are ready to install it.

Handle with Care

●

To protect its ﬁnish and avoid damage before and a er installa on, please handle the product with care. For care and cleaning

ps a er installa on, please refer to the Care and Cleaning Guide in this instruc on guide.

IMPORTANT: Recommended for professional installers only. The installer maintains responsibility for installing the product safely.

1. Install the Vanity

Use a stud ﬁnder to locate and mark the wall studs.

●

Li and place the vanity cabinet in posi on against the ﬁnished wall. Make sure

●

the top is level and the supply valves clear any drawers in the cabinet.

Drill pilot holes through the vanity back and the ﬁnished wall. For holes not inline

●

with studs, push or hammer in wall anchors that are made for your wall surface.

Secure the cabinet to the ﬁnished wall with screws.

●

2. Install the Countertop

Assemble the faucet and the sink drain to the countertop.

●

Run a bead of silicone adhesive around the top of the vanity cabinet. Place the

●

sink countertop on top of the cabinet and press ﬁrmly in place. Let the silicone

adhesive cure.

Connect the water supply lines and the drain.

●

Reinstall the cabinet drawer(s).

●

Apply a bead of caulk along the back edge against the wall. Clean up any excess.

●

Allow 24 hours to dry.

Turn on the water to test for leaks.

●

3. Install the Mirror

Examine the type of brackets on the back of the mirror.

●

Hold the mirror ﬂush and level against the wall in the desired posi on. Mark the

●

mirror's placement with a pencil around the top and bo om corners. Set the

mirror aside with care.

Use a stud ﬁnder to locate studs on the wall. Mark the loca on with a pencil.

●

Measure the distance from the top of the mirror to the brackets on the back of

●

the mirror. Use this measurement to mark the posi ons for the screws on the

wall. Make sure the marks are straight with a level.

Drill pilot holes into the marks for the screws . If the screws will not be mounted

●

on studs, hammer in wall anchors.

Insert screws, leaving a short length of screw extending from the wall surface.

●

Hang the mirror.

LEGAL DISCLAIMER:

This instruc on guide is done as a public service to customers of Dawn Kitchen & Bath Products, Inc. ("Dawn"). For special situa ons or further assistance, please consult professionals.

●

All products should be inspected by customers upon receipt and before any installa on. Any defec ve product should be reported immediately and should NOT be installed.

●

Requirements may vary for installa on in a granite, marble, stone, or butcher block countertop.

●

Installa on by professional installers is highly recommended. Dawn assumes no liability for any damages incurred through the use of informa on provided in this guide.

●

MATERIALS & TOOLS

BEFORE YOU BEGIN

INSTALLATION

INSTALLATION GUIDE AACS-3001