- ページ 4

セキュリティシステム ADEMCO VISTA-15PのPDF プログラミング・マニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO VISTA-15P 17 ページ。 Programming auto arming and disarming schedules
ADEMCO VISTA-15P にも： クイック・インストール・マニュアル (2 ページ), プログラミング・マニュアル (17 ページ), ユーザーマニュアル (20 ページ), クイック・インストール・マニュアル (2 ページ), クイック・インストール・マニュアル (2 ページ), プログラミング・マニュアル (2 ページ), クイックマニュアル (2 ページ)

ページを印刷する
ADEMCO VISTA-15P プログラミング・マニュアル
NOTE: Entry of a number other than one specified will give unpredictable results.
For fields *43- *46: Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; [#+15 for F]. Enter [ ✱ ] as the fourth digit if a 3-digit account number (for 3+1 dialer
reporting format) is used. Enter 0 as the first digit of a 4-digit account number for Nos. 0000-0999. Exit field by pressing ✱ (and press next field number) if only 3
digits are used. E.g., For Acct. B234, enter: #+11| 2 | 3 | 4
✱
43 PARTITION 1 PRIMARY SUBS. ACCT. No.
✱
44 PARTITION 1 SECONDARY SUBS. ACCT. No.
✱
45 PARTITION 2 PRIMARY SUBS. ACCT. No.
✱
46 PARTITION 2 SECONDARY SUBS. ACCT. No.
✱
PHONE SYSTEM SELECT
47
✱
48
REPORT FORMAT
✱
49
SPLIT/DUAL REPORTING
✱
50
15 SEC DIALER DELAY (BURG)
✱ 53
SECOA/RADIONICS SELECT
✱ 54
DYNAMIC SIGNALING DELAY
✱ 55
DYNAMIC SIGNALING PRIORITY
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES ( ✱ 59 – ✱ 76, & ✱ 89):
For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.
A 0 ( not #+10) in the first box will disable a report. A 0 ( not #+10) in the second box will result in automatic advance to the next field.
For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.
A 0 ( not #+10) in the second box will eliminate the expanded message for that report. A 0 ( not #+10) in both boxes will disable the report.
For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the first box, to enable zone to report (entries in the second boxes are ignored).
A 0 ( not #+10) in the first box disables the report.
SYSTEM STATUS REPORT CODES ( ✱ 59– ✱ 68)
✱ 59
EXIT ERROR REPORT CODE
✱ 60
TROUBLE REPORT CODE
✱ 61
BYPASS REPORT CODE
✱ 62
AC LOSS REPORT CODE
✱ 63
LOW BAT REPORT CODE
✱ 64
TEST REPORT CODE
✱ 65
OPEN REPORT CODE
✱ 66
ARM AWAY/STAY RPT CODE
| | |
| | |
|
|
|
|
[1]
primary
[0]
[0]
[0]
UL: see installation instructions for requirements
[0]
See box above.
|
[00]
See box above.
|
[00]
See box above.
|
[00]
See box above.
|
[00]
See box above.
|
[00]
See box above. Use Scheduling mode to set periodic test reports.
[0,0,0]
Part. 1 Part. 2 Common
Away Stay
Away Stay
Part. 1
Part. 2
– 4 –
See box above for entries. To clear entries
[FFFF]
from field, press * 43 *.
See box above for entries. To clear entries
[FFFF]
from field, press * 44 * .
See box above for entries. To clear entries
|
[FFFF]
from field, press * 45 * .
See box above for entries. To clear entries
|
[FFFF]
from field, press * 46 * .
If Cent. Sta. IS NOT on a WATS line:
0=Pulse Dial; 1=Tone Dial;
if Cent. Sta. IS on a WATS line:
2 = Pulse Dial ; 3 = Tone Dial
0 = 3+1, 4+1 ADEMCO L/S STANDARD
[70]
1 = 3+1, 4+1 RADIONICS STANDARD
secondary
2 = 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
6 = 4+2 ADEMCO EXPRESS
7 = ADEMCO CONTACT ID® REPORTING
8 = 3+1, 4+1 ADEMCO L/S EXPANDED
9 = 3+1, 4+1 RADIONICS EXPANDED
0 = Disable (Backup report only)
Primary Phone No.
Phone No.
1 = Alarms, Restore, Cancel
2 = All except Open/Close, Test Open/Close,
3 = Alarms, Restore, Cancel
4 = All except Open/Close, Test All
5 = All
0 = no UL: must be "0"; 1 = yes
0 = Radionics (0-9, B-F)
1 = SESCOA (0-9 only reporting)
Select "0" for all other formats.
Delay selectable from 0 to 225 secs in 15-sec
[0]
increments.
0 = no delay (both signals sent), 1 = 15 secs,
2 = 30 secs, etc. UL: must be "0"
0 = Primary Dialer first; 1 = Long Range Radio
[0]
first.
See box above.
[0,0,0,0,0,0] See box above.
Away Stay
Common
Second
Others
Test
All
All