- ページ 5

セキュリティシステム ADEMCO VISTA-15PのPDF プログラミング・マニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO VISTA-15P 17 ページ。 Programming auto arming and disarming schedules
ADEMCO VISTA-15P にも：クイック・インストール・マニュアル (2 ページ), プログラミング・マニュアル (17 ページ), ユーザーマニュアル (20 ページ), クイック・インストール・マニュアル (2 ページ), クイック・インストール・マニュアル (2 ページ), プログラミング・マニュアル (2 ページ), クイックマニュアル (2 ページ)

ページを印刷する

✱ 67

RF XMTR LOW BAT REPORT CODE

✱ 68

CANCEL REPORT CODE

RESTORE REPORT CODES ( ✱ 70 – ✱ 76)

✱ 70

ALARM RESTORE RPT CODE

✱ 71

TROUBLE RESTORE RPT CODE

✱ 72

BYPASS RESTORE RPT CODE

✱ 73

AC RESTORE RPT CODE

✱ 74

LOW BAT RESTORE RPT CODE

✱ 75

RF XMTR LO BAT RST RPT CODE

✱ 76

TEST RESTORE RPT CODE

OUTPUT AND SYSTEM SETUP ( ✱ 77 – ✱ 93)

* 77

DAYLIGHT SAVINGS TIME

START\END MONTH

* 78

DAYLIGHT SAVINGS TIME

START\END WEEKEND

✱ 84

AUTO STAY ARM

✱ 85

CROSS ZONE TIMER

This option not for use in UL installations.

✱ 86

CANCEL VERIFY

✱ 87

MISC. FAULT DELAY TIME

(used with Configurable Zone Types "digit 6")

✱ 89

EVENT LOG FULL REPORT CODE

✱ 90

EVENT LOG ENABLES

✱ 91

OPTION SELECTION

✱ 92

PHONE LINE MONITOR ENABLE

UL: see Inst. Instructions for requirements

✱ 93

No. OF REPORTS IN ARMED PERIOD

PER ZONE (Swinger Suppression)

[00]

[0]

[00]

0 = Disabled

[4][10]

1-12 = January-September (1 = Jan, 2 = Feb, etc)

#+10 = October; #+11 = November; #+12 = December

0 = disabled, 1 = first, 2 = second, 3 = third

[1][5]

4 = fourth, 5 = last, 6 = next to last, 7 = third to last

0 = no, 1 = partition 1 only

[0]

2 = partition 2 only, 3 = both partitions

0 = 15 seconds

[0]

1 = 30 seconds

2 = 45 seconds

3 = 60 seconds

4 = 90 seconds

5 = 2 minutes

(assign cross zones on zone list 4, with *81 Menu mode)

0 = no, 1 = yes

[0]

0 = 15 seconds

[0]

1 = 30 seconds

2 = 45 seconds

3 = 60 seconds

4 = 90 seconds

5 = 2 minutes

See box on previous page for report code entries.

[00]

0 = None; 1 = Alarm/Alarm Restore

[3]

2 = Trouble/Trouble Restore;

4 = Bypass/Bypass Restore;

NOTE : System messages are

8 = Open/Close. Example: To select "Alarm/Alarm

logged when any non-zero

Restore", and "Open/Close", enter 9 (1 + 8); To select

selection is made.

all, enter #15.

0 = None

[8]

4 = AAV UL: do not use AAV

8 = Exit Delay Restart

Multiple choice example: for AAV (4) + Exit Delay

restart (8) enter # + 12.

Digit 1:: 0 = disabled, 1-15 = 1 min - 15 min

[0,0]

Digit 2:

0 = Keypad display when line is faulted

1 = Keypad display plus keypad trouble sound

2 = Same as "1", plus programmed output device

STARTS. If either partition is armed, external sounder

activates also. NOTE: Output Device must either be

programmed to be STOPPED in field ✱80 or

STOPPED by Code + # + 8 + output number.

0 = Unlimited Reports; 1 = 1 report; 2 = 2 reports

[0]

UL: must be "0"

– 5 –

See box on previous page.

UL: must be enabled if wireless devices are used

See box on previous page.

UL: must be enabled if wireless devices are used

See box on previous page.

6 = 2-1/2 min

7 = 3 min

8 = 4 min

9 = 5 min

#+10 = 6 min

#+11 = 7 min

6 = 2-1/2 min

7 = 3 min

8 = 4 min

9 = 5 min

#+10 = 6 min

#+11 = 7 min

UL: may only be used on non-burglar alarm/ non-fire alarm

zones when used in fire and/or UL burglar alarm installation

(#+10 = 10 min; #+11 = 11 min; #+12 = 12 min;

#+13 = 13 min; #+14 = 14 min; #+15 = 15 min)

#+12 = 8 min

#+13 = 10 min

#+14 = 12 min

#+15 = 15 min

#+12 = 8 min

#+13 = 10 min

#+14 = 12 min

#+15 = 15 min