- ページ 10

ガレージドアオープナー Automatic Technology Australia EasyRoller GDO-4のPDF 取付説明書および取扱説明書をオンラインで閲覧またはダウンロードできます。Automatic Technology Australia EasyRoller GDO-4 16 ページ。

ページを印刷する

lnstallation

conr...

CLOSE LIMIT ADJUSTMENT

(h)

Press in

and

hold

the

Red

Close lnch Button.The door

should start

closing. Release

the

inch button when

the door

reaches

the

desired

closed

limit

stop

position. lf

the

Red

LED (see

Fig. 14) is illuminated

and the

desired limit

position

has been

reached

then the

limit

adjustment is complete.

the

Red LED is illuminated but the

door

has

not reached,

has

gone

past the

desired

position,

you

have

adjust

the Red

Fine

Adjustment

Screw

(see

Fig.

14).

Adjust

the

screw

clockwise

the door

less. To

the door

more adiust the

screw anticlockwise. Each

complete

revolution of

the

adjustment screw

is equal

to approximately

1Omm

of door travel.

NOTE: lf

the door has

not reached

the desired

limit position

by more

than

30mm,

then it is

recommended

that

the

red

limits

cam

be adjusted again before

the

red

fine

adjustment

screw is adjusted.

FIXING OF

DOOR CURTAIN

TO DRUM

WHEEL

The

Door

Curtain

has

be secured to the drum

wheel

with

suitable fasteners.

(a)

With

the door

the

fully

closed position

mark

the curtain

(as per

Fig.

15)

both ends of the

door.

(b)

Open

door

slightly

have access to

the

marked positions. Secure the

curtain

drum

wheel

using

self

drilling screws (two

on each

end).

The

screws should be

least 90

degrees apart as per Fig.

15.

7. SETTING OF CLOSE SAFETY OBSTRUCTION AND

OPEN

FORGE

lmportant:

The

setting for the

open

and

obstruction forces are the

most

important adjustments

that are

made in the

whole

installation

procedure. Make sure that the

force

(load

)

is adjusted

correctly as

per the

installation instructions. Failure

adjust

these

settings

correctly

could

result in

serious

personal and

/or property

damage.

The end

user

musl

informed

that they

must

test at

regular intervals (once

month

recommended)

these settings

and

the

necessary adiustments

made

required.

Note:

The Open and

Obstruction

Force ad.lustments procedure are

the

same

for

Left

Right Hand installation.

7.1 CLOSE SAFETY OBSTRUCTION

FORCE

ADJUSTMENT

(a)

Fully open

the door

pressing

and

holding

the

green

inch button.

The

door

will stop

automatically when

the open

limit

position is

reached.

(b)

Turn

the

Red

Force Shaft

fully

clockwise. Press the

Yellow

O/S/C

(open, stop,close) button

(see

Fig. 16) momentarily,

the

door

should

stgrt

closing. As

the door

is closing

turn the

Red Shaft slowly

anticlockwise until the

door stops

momentarily

then

reverses to the

open

position.

(c)

Turn

the

Red

Shaft

10'

clockwise, Press the Yellow button

close the

door. lf

the door

reverses by itself, readjust

the

Red Shaft a

further

clockwise. Keep adjusting in

this manner

until

the door can

complete

the full closing cycle.

FIG. i4

DRUI,,I

VHETL

+-+

(o)

(b)(c)

FIG.