- ページ 8

ガレージドアオープナー Automatic Technology Australia EasyRoller GDO-4のPDF 取付説明書および取扱説明書をオンラインで閲覧またはダウンロードできます。Automatic Technology Australia EasyRoller GDO-4 16 ページ。

ページを印刷する

lnstallation

cont...

FIXING DRIVE ASSEMBLY TO

DOOR

The

Easy Roller Drive Assembly

can

be fixed to

the

Roll Up

Garage

Door

in a variety of ways. Below we

will describe one

method of fixing. Make

sure

there

enough

room (135mm

from end

door

shaft

the wall) to

slide drive assembly

onto

shaft.

PLEASE

NOTE:

THE

INSTRUCTIONS FOR FIXING OF

THE

DRIVE

ASSEMBLY

THE

DOOR IS

FOR

RIGHT HAND INSTALLATION.

FITTING DRIVE ASSEMBLY

DOOR

(see

Fig.6,Fig.7,

and

Fig.8

(a)

Check

that the door shaft

bolt

is securely

tightened

the

left hand

side of

the

door.

(b)

Baise

the door

and

tie a

rope around

the

centre

secure

the

roll.

(c)

Support the

right hand end of the

door with

suitable

prop, e.g. step

ladder

and soft

padding

protect

door

surface.

STOP.

WARNING: DO

NOT ALLOW CHILDREN/PEFISONS

AHOUND

THE

DOOR

WHEN

PROPPED.

SERIOUS PERSONAL

INJURY

AND

PROPERTY DAMAGE

CAN

RESULT FFIOM FAILURE

FOLLOW THIS WARNING.

(d)

Check

that step

3.1a was completed.

Carefully

loosen

and

remove the

right hand

door shaft

U bolt.

(e)

Make sure

that

the door

supporting prop

is secure.

While

the

door

supported

remove

the

right hand

door

mounting bracket from wall.

(f)

Remove

the

Drive Assembly

from

packaging. Try

and

rotate

the

drive

gear by pushing on the fork. lf

the

gear

does not

rotate

the

manual

mode has

be selected.

select

pull

the string

handle

downwards,

then

release

slowly.

The

drive

gear should now

rolate.

(g)

Slide Drive Assembly over

the door axle

making sure

that

the fork

extends into

and

over one of

the

spokes of

the

door

drum wheel.

(h)

Refit

the door

mounting bracket to

the

wall. ln

some

cases

the

bracket

may

have

be repositioned.

Retighten

the

door shafi

U bolt.

Remove door

supporting

prop

and untie

rope

from

curtain.

Straighten

the

Drive Assembly

and

position

per

figure

Tighten

the

two

locking bolts

firmly to secure

Drive Assembly.

Check

the

manual operation of

the door

by raising

and

lowering the

door.

The

door

should

run

smoothly and

not catch

on any part

of the

Drive Assembly.

SETTING

LIMIT

SWITCHES

The

Limit Cams,

Limii

Fine

Adjustment

Screws

and Door lnch

Buttons are

colour coded

make

the

setting of

the

limits

user

friendly as

possible.

The

GREEN colours for

OPEN

LIMIT SETTING.

The

RED colours for

CLOSE LIMIT SETTING.

5.1

SETTING LIMITS

FOR RIGHT

HAND

INSTALLATION

(a)

With

the

Drive Assembly in manual mode (disengage,

see

Fig.

12),

move

the door

up by hand

the desired

open

position.

(b)

Remove

the

Light Diffuser

(see

Fig. 9). Rotate by

hand

anticlockwise direction

the

green limit

cam (see

Fig. 10) until the cam

clicks

the open

limit switch.

(c)

Move the

door down

by hand to

the

desired

closed

position.

(d)

Rotate by

hand

in a clockwise direction

the

red limit

cam

(see fig.

11)

until

ihe

cam clicks the

limit switch.

(e)

Connect

power lead from

the

Drive

Assembly

into a

general purpose

power

outlet

installed by

licensed qualified electrical

contractor.

Turn

the

Power On.

Fle-engage

the

drive

gear

by pulling down on

the string

handle and

then

releasing

slowly (see

Fig.

12)

(i)

(o)

CHECK IF

,U'

BOLT

TI6HTENED

(d)

REMOVE

RIGH'I

-U'

BOLT

FIG.

REMT]VE

LIGHT

DIFUSER

FIG.

FI6.