- ページ 2
I/Oシステム AutomationDirect Productivity2000 P2-8AD4DA-2のPDF マニュアルをオンラインで閲覧またはダウンロードできます。AutomationDirect Productivity2000 P2-8AD4DA-2 8 ページ。
ページを印刷するInput Specifications
Input Channels
8 inputs (1 common)
Input Ranges
0–5 VDC, 0–10 VDC
Signal Resolution
12–16 bit, depending on input resolution
0 - 5V Input Resolution &
Fine: 7.1 ms, 76μV, 16 bit
Update Rate
Medium: 1.78 ms, 305μV, 14 bit
(See Note 1)
Coarse: 444μs, 1.22 mV, 12 bit
0 - 10V Input Resolution &
Fine: 7.1 ms, 152μV, 16 bit
Update Rate
Medium: 1.78 ms, 610μV, 14 bit
(See Note 1)
Coarse: 444μs, 2.44 mV, 12 bit
Data Range
0–65535 counts
Maximum Continuous Overload ±100V, voltage input
Input Impedance
1MΩ (±10%) voltage input
Hardware Filter Characteristics
Low pass 1st order, -3dB @ 80Hz
Fine 56.8 ms
All Channel Update Rate
Medium: 14.24 ms
(See Note 2)
Coarse: 3.55 ms
Conversion Method
Successive approximation
Accuracy vs. Temperature
±15ppm/°C maximum
Maximum Inaccuracy
0.1% of range
±0.015% of range maximum
Linearity Error (end to end)
Monotonic with no missing codes
Input Stability and Repeatability ±0.025% of range (after 10 minute warm-up)
Full Scale Calibration Error
±0.05% of range maximum
(not including offset)
Offset Calibration Error
±0.05% of range maximum
Maximum Crosstalk
-96dB, 1LSB
External DC Power Required
24VDC (-20% / +25%), 130mA
Note 1: The Input Resolution of Fine returns 16 bit resolution. Medium and Coarse are 14
and 12 bit respectively. The 12 and 14 bit input values are scaled to 0–65535.
Note 2: Valid when all channels are set for the same Input Resolution.
2
www.productivity2000.com
Output Specifications
Output Channels
4 (1 common)
Module Signal Output Range
0–10 VDC, 0–5 VDC
Output Signal Resolution
16-bit
0–5 V = 76μV/count
Resolution Value of LSB
0–10 V = 152μV/count
(least significant bit)
1 LSB = 1 count
Data Range
0–65535 counts
Output Type
Voltage sourcing/sinking at 10mA maximum
Output Value in Fault Mode
0V
Load Impedance
≥1.5 kΩ
Maximum Capacitive Load
0.01μF
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range
Maximum Full Scale Calibration
±0.065% of range maximum
Error (not including offset error)
Maximum Offset Calibration Error
±0.065% of range maximum
±25ppm/°C max full scale calibration change
Accuracy vs. Temperature
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
±0.015% of full scale
Linearity Error (End to End)
Monotonic with no missing codes
Output Stability and Repeatability
±0.015% after 10 minute warm-up typical
Output Ripple
0.01% of full scale at 50/60 Hz
Output Setting Time
500μs max, 5μs min (full scale change)
All Channel Update Rate
5ms
Maximum Continuous Overload
Outputs current limited to 15mA typical
Type of Output Protection
15VDC peak output voltage
Output Signal (power-up, -down)
0V
Tech Support 770-844-4200