- ページ 2
煙警報器 ADEMCO 4192のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。ADEMCO 4192 4 ページ。 Smoke detector base/transponder
ページを印刷する
-
.
VECTOR
CONTROL
--
4190
4196
0
c
,
Diagram
3. TYPICAL
WIRING
TO VECTOR
SERIES
C-COM
MOUNTING
THE No. 4192
The ADEMCO
No. 4192 SMOKE
DETECTOR
BASE!TRANSPONDER
mounts
directly
to 3-inch
or 4-tnch
octagon
lunctron
boxes,
or with the
addition
of a plaster
ring or an ADEMCO
specrally
designed
adapter
plate,
to a 4-inch
square
lundron
box
OCTAGON
BOX
Diagram
4:
TYPICAL
MOUNTING
DETAIL
_ --_
,.,'..
.;------;
',\\
LEFToR t'
i
DEECTOA
/
BASE
Diagram
5: DETAIL
FOR MOUNT-
Diagram
6: DETAIL
FOR MOUNT-
ING DETECTOR
BASE ON 4-INCH
ING DETECTOR
BASE ON A 4-
SQUARE
JUNCTION
BOX USING
PLASTER
RING
INCH SQUARE
JUNCTION
BOX,
OR DIRECTLY
TO CEILING,
USING
ADEMCO
ADAPTER
NOTE:
Only two mounting
screws
are provided
with each
detector
base.
The additional
screws
shown
in Figure
5 and 6 for mounting
the
plaster
ring or the adapter
bracket
on the square
junction
box may
be supplied
or purchased
with the junction
box.
TESTING
THE
lh%TALLATlON
Once
all the detector
bases
have
been wired
and mounted,
and the
wiring
has been
checked,
the detector
heads
may be installed
in the
loop
bases.
To install the detector
heads,
line up the terminals
in the base with
the holes in the bottom
of the detector
heads,
insert the detector
head,
and
turn it about
10 degrees
clockwise
until the detent
clicks
into place.
NOTE:
If a detector
goes into alarm,
it will reset only if all products
of
combustion
are cleared
from the senstng
chamber.
If not. remove
the detector
head from the base to cut off its power.
Then reinstall
the detector
head in the base.
TAMPER-PROOF
FEATURE
These
detector
bases
also include
an optional
tamper-proof
tab that pre-
vents
removal
of the detector
without
the use of a tool. The tab is slipped
into a slot in the rim of the detector
cover
before
the detector
head
is
installed
in the detector
base. Then the locking
tab is pushed
into the base
(See Frgures
7A and 78 on the next page).
This prevents
the detector
head
from
being turned
counterclockwise
and removed,
unless
the locking
tab is
first released.
To remove
the detector
head, insert a small-bladed
screw
driver
into release
slot of tab and slide it out of the base. Then turn the
detector
head counterclockwise
about
10 degrees.
-__^--..
-..-
-_.
CAUTION:
TO AVOID
POSSIBLE
DAMAGE
To clRculT,
DISCON-
-
NECT
BOTH
POLLING
LOOP
WIRES
AT CONTROL
PANEL
PRIOR
TO INSTALLATION
OR SERVICING
THIS
UNIT.
ALSO
ONCE
DETECTOR
HEAD
IS INSTALLED
IN THE
BASE,
THE
OPTIONAL
TAMPER-PROOF
TAB MUST
BE PUSHED
INTO
THE
BASE
SO THAT
WITHOUT
TOOL,
DETECTOR
HEAD
CANNOT
BE
REMOVED
FROM
THE
BASE.
(SEE
FIGURES
7A AND
78).
.
-.
_