ADEMCO 4192 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} ADEMCO 4192. ADEMCO 4192 4 pagina's. Smoke detector base/transponder

Pagina afdrukken

VECTOR

CONTROL

4190

4196

Diagram

3. TYPICAL

WIRING

TO VECTOR

SERIES

C-COM

MOUNTING

THE No. 4192

The ADEMCO

No. 4192 SMOKE

DETECTOR

BASE!TRANSPONDER

mounts

directly

to 3-inch

or 4-tnch

octagon

lunctron

boxes,

or with the

addition

of a plaster

ring or an ADEMCO

specrally

designed

adapter

plate,

to a 4-inch

square

lundron

box

OCTAGON

BOX

Diagram

TYPICAL

MOUNTING

DETAIL

_ --_

,.,'..

.;------;

',\\

LEFToR t'

DEECTOA

BASE

Diagram

5: DETAIL

FOR MOUNT-

Diagram

6: DETAIL

FOR MOUNT-

ING DETECTOR

BASE ON 4-INCH

ING DETECTOR

BASE ON A 4-

SQUARE

JUNCTION

BOX USING

PLASTER

RING

INCH SQUARE

JUNCTION

BOX,

OR DIRECTLY

TO CEILING,

USING

ADEMCO

ADAPTER

NOTE:

Only two mounting

screws

are provided

with each

detector

base.

The additional

screws

shown

in Figure

5 and 6 for mounting

the

plaster

ring or the adapter

bracket

on the square

junction

box may

be supplied

or purchased

with the junction

box.

TESTING

THE

lh%TALLATlON

Once

all the detector

bases

have

been wired

and mounted,

and the

wiring

has been

checked,

the detector

heads

may be installed

in the

loop

bases.

To install the detector

heads,

line up the terminals

in the base with

the holes in the bottom

of the detector

heads,

insert the detector

head,

and

turn it about

10 degrees

clockwise

until the detent

clicks

into place.

NOTE:

If a detector

goes into alarm,

it will reset only if all products

combustion

are cleared

from the senstng

chamber.

If not. remove

the detector

head from the base to cut off its power.

Then reinstall

the detector

head in the base.

TAMPER-PROOF

FEATURE

These

detector

bases

also include

an optional

tamper-proof

tab that pre-

vents

removal

of the detector

without

the use of a tool. The tab is slipped

into a slot in the rim of the detector

cover

before

the detector

head

installed

in the detector

base. Then the locking

tab is pushed

into the base

(See Frgures

7A and 78 on the next page).

This prevents

the detector

head

from

being turned

counterclockwise

and removed,

unless

the locking

tab is

first released.

To remove

the detector

head, insert a small-bladed

screw

driver

into release

slot of tab and slide it out of the base. Then turn the

detector

head counterclockwise

about

10 degrees.

-__^--..

-..-

-_.

CAUTION:

TO AVOID

POSSIBLE

DAMAGE

To clRculT,

DISCON-

NECT

BOTH

POLLING

LOOP

WIRES

AT CONTROL

PANEL

PRIOR

TO INSTALLATION

OR SERVICING

THIS

UNIT.

ALSO

ONCE

DETECTOR

HEAD

IS INSTALLED

IN THE

BASE,

THE

OPTIONAL

TAMPER-PROOF

TAB MUST

BE PUSHED

INTO

THE

BASE

SO THAT

WITHOUT

TOOL,

DETECTOR

HEAD

CANNOT

REMOVED

FROM

THE

BASE.

(SEE

FIGURES

7A AND

78).