- ページ 3

ネットワーク・ルーター 2gig Technologies 2GIG-BRDG1-900のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。2gig Technologies 2GIG-BRDG1-900 4 ページ。 Go!bridge ip communicator

ページを印刷する

Verifying the Settings

In addition to verifying the settings after configuring the Go!Bridge IP

Communicator, you can also verify the settings at any time as follows:

At the Control Panel's Home screen, tap Security.

Tap Menu.

Tap Toolbox.

In the Enter Your Code to Access the Toolbox screen, enter the

master user code.

Tap → to scroll to the Toolbox (3 of 3) screen. Then tap Go!Bridge

IP Communicator Status.

A summary screen displays the following information:

•

Network Configuration. The network type configuration.

•

IP Address. The IP Address for the Go!Bridge IP Communicator.

This is a 32‐bit numeric address that identifies the device on the

network.

•

Subnet Mask. The subnet mask for the network. All devices that

are joined to a network belong to a subnetwork.

•

Gateway. The IP Address for the access point to the external

network. Typically, this is the IP Address of the local network

router or node that control traffic for your ISP.

•

MAC Address. This is the Media Access Control (MAC) Address.

It is a physical address that is encoded to the Go!Bridge IP

Communicator during the manufacturing process.

Testing

The Go!Bridge IP Communicator tests the network connection to the

third‐party monitoring service. A report shows if Go!Bridge IP

Communicator has successfully connected (or failed to connect) to the

external server.

Registration

To register the Go!Bridge IP Communicator with the monitoring service,

refer to your specific provider's registration instructions.

SPECIFICATIONS

Wireless Signal Range

500 ft (152.4 m), open air, with Wireless Control Panel

Transceiver

Silicon Labs SI1001‐E‐GM2

Transceiver Frequency

25 channel frequency‐hopping spread spectrum, 403

kHz channel spacing (910.2‐920.275 MHz)

Modulation Type

GFSK modulation, 128 kpbs

RF Power

+19dBm Maximum

Ethernet

10/100 BaseT

Dimensions (L x W x H)

6.24 x 4.5 x 1 in (159 x 114 x 25 cm)

Weight

9.6 oz

Housing Material

Cycoloy™ Resin C2800 (Rated to UL 94 V‐0:

Flammability Standard)

Color

White

Operating Temperature ‐32° F to 120° F, (0° C to +49° C)

Relative Humidity

5‐95% Non‐Condensing

Operating Voltage

5VDC

Certification

ETL, FCC, IC, IFETEL, and NOM

Important Note

Should the local network lose Internet access due to a power outage or

interruption, the Go!Bridge IP Communicator is not equipped with a

backup battery system. To best prepare for power failures and to ensure

the security system maintains Internet access with the monitoring

service for life‐safety communications during power failures, the local

network must have a dedicated Uninterrupted Power Supply (UPS) or

backup battery solution from a third‐party manufacturer in place.

Linear LLC does not supply, provide, recommend, or test the Go!Bridge

with any UPS or battery backup solution. It is also assumed that owner's

Internet Service Provider (ISP) maintains a backup battery (or power

generator) for their remote network equipment.

Go!Bridge IP Communicator | Installation Instructions

REGULATORY INFORMATION

Wireless Product Notice

Radio controls provide a reliable communications link and fill an

important need in portable wireless signaling; however, there are some

limitations which must be observed.

•

For United States Installations Only: The radios are required to

comply with FCC Rules and Regulations as Part 15 devices. As

such, they have limited transmitter power and therefore limited

range (approximately 400 ft.).

•

A receiver cannot respond to more than one (1) transmitted

signal at a time and may be blocked by radio signals that occur

on or near their operating frequencies, regardless of code

settings.

•

Changes or modifications to the device may void FCC

compliance.

•

Infrequently used radio links should be tested regularly to

protect against undetected interference or fault.

•

A general knowledge of radio and its vagaries should be gained

prior to acting as a wholesale distributor or dealer, and these

facts should be communicated to the end users.

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for

Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates and

can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one(1) or more of the

following measures.

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected

•

Consult the dealer or an experienced radio/TV technician for

help

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate

the equipment.