- ページ 2

医療機器 dynarex 10522のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。dynarex 10522 2 ページ。 Geri chair recliner

ページを印刷する

ASSEMBLY INSTRUCTIONS

NOTE: After removing all components from the carton, engage the two caster locks before beginning

Upholstered Back:

1. Remove cardboard shipping retainers from around Gas

Spring Cylinder. Rotate the hinge on the gas spring so that

it is perpendicular to the upholstered back. (See figure 1)

2. Lift the upholstered back from the sides and place it

horizontally with the upright back tubes resting on the

recliner frame. (See figure 2)

3. Undo hook and rings on side panels, both sides so

mounting holes are exposed. Align the holes on the upright

back tubes of the upholstered back with the holes on the

seat frame. Replace the clevis pins through the mounting

holes.

4. Secure the two clevis pins by replacing the bridge clips.

FIGURE 1

FIGURE 2

SIDE TABLES AND HEADREST

Side Tables:

1. To place either table in raised position: raise table all the way up

and slide in until tabs engage slots in mount bracket. Press down

lightly on table to ensure lock tabs are engaged.

2. To return table to self-storing position: Lift table up until tabs

disengage from slots. Slide out and allow table to lower. (See

figure 5)

Articulating Headrest:

Articulating headrest may be adjusted to a comfortable position by

pulling forward or pushing back.

SEAT POSITIONING

Adjusting the recline:

Lock the rear casters. While holding the push

bar, squeeze the piston spring release handle.

To lower, push back on padded push handle.

To raise, pull forward on padded push handle.

To achieve the Shock Position, follow the

above steps and continue to lower the back

until the shock position pictured is achieved.

5. Raise the upholstered back to vertical position. Tuck the

plastic skirt at rear of upholstered back behind cross brace

of seat frame. Align the hinge at the bottom of the gas

spring with the holes in the "U" bracket in the seat frame

cross brace. While holding the back with one hand, secure

the gas spring hinge to the "U" bracket by replacing the

bolt with the other hand. Secure the bolt by replacing the

nut. (See figure 3)

Seat Frame:

1. Align holes in arm support mount to mounting holes in seat

frame. (See figure 4)

2. Insert screws through arm support mount and seat

frame holes. Secure screw with nut.

3. Repeat for other side.

FIGURE 3

Table (Disengaged Position)

Armrest

Clevis Pin

Table Mount

Bracket

Tabs engage into

slots on table

mount bracket

Table (Stored Position)

FIGURE 5

Recline Position 1

Recline Position 2

assembly..

Pedal protrudes

Push down

Every Three Months:

• Check and clean casters.

• Tighten nuts.

• Check brakes on casters.

• Check and clean lock recline mechanism.

For upholstery maintenance and stain removal,

FIGURE 4

the following hints will be helpful:

• Ordinary Dirt: Wash with warm water and a mild

soap or detergent.

• Stubborn Dirt: Using a soft bristle brush, follow

directions above.

Your Dynarex Geri Chair Recliner is warrantied to be

Table (Engaged Position)

free of defects in materials and workmanship for a

limited lifetime on the frame, and one (1) year on

upholstery and all moving parts, from original date of

purchase, for use by the original purchaser. This item

was built to exacting standards and carefully inspected

prior to shipment. This Warranty is an expression of our

confidence in the materials and workmanship of our

products and our assurance to the consumer of

dependable service.

The Warranty shall not apply under the following

conditions: problems arising from normal wear;

problems arising from failure to adhere to the product

instructions; problems arising from misuse, negligence,

accident or improper operation, maintenance or

storage; problems arising from modifications or

unauthorized repairs, parts or attachments; products

SYMBOL GLOSSARY

For an explanation of symbols

used in Dynarex packaging, visit

Shock Position

dynarex.com/symbols.php

CASTER OPERATIONS

TOTAL LOCK: Step on the rear pedal

of the caster until the pedal engages.

The front of pedal will protrude from

wheel cover.

UNLOCK: Step on the protruding front

part of the pedal to disengage lock to unlatch.

NOTE: This chair is equipped with four swivel

casters for improved maneuverability. The rear

casters are also equipped with locking features.

MAINTENANCE/CLEANING

• Ground-in Dirt: Scrub with powdered cleanser or

similar detergent.

• Chewing Gum: Scrape carefully.

• Nail Polish and Remover: Blot immediately to prevent

damage.

• Ball Point Pen: Blot immediately with a white cloth

dampened in water or mineral oil.

• Waxing and Refinishing: Improve wearability. Use any

quality paste wax.

NOTE: A diluted solution of 10% (or less) of bleach or

Clorox

may be used when cleaning this chair.

WARRANTY

where the serial number has been removed or defaced;

problems with non-durable components, such as

rubber accessories, casters, and grips, which are

subject to normal wear and need periodic replacement.

Dynarex shall not be liable for any consequential or

incidental damages whatsoever. Dynarex shall repair or

replace defective products at its option. The foregoing

warranty is exclusive and in lieu of other express

warranties, if any, including the implied warranties of

merchantability and fitness of a particular purpose. The

remedy for any violation of the implied warranty shall

be limited to repair or replacement of the defective

product pursuant to the terms contained herein.

If you have a question about your Dynarex device or

this warranty, please contact an authorized Dynarex

dealer.

Push down

R200701