dynarex 10522 Посібник із швидкого старту - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Медичне обладнання dynarex 10522. dynarex 10522 2 сторінки. Geri chair recliner
Друкувати сторінку
ASSEMBLY INSTRUCTIONS
NOTE: After removing all components from the carton, engage the two caster locks before beginning
Upholstered Back:
1. Remove cardboard shipping retainers from around Gas
Spring Cylinder. Rotate the hinge on the gas spring so that
it is perpendicular to the upholstered back. (See figure 1)
2. Lift the upholstered back from the sides and place it
horizontally with the upright back tubes resting on the
recliner frame. (See figure 2)
3. Undo hook and rings on side panels, both sides so
mounting holes are exposed. Align the holes on the upright
back tubes of the upholstered back with the holes on the
seat frame. Replace the clevis pins through the mounting
holes.
4. Secure the two clevis pins by replacing the bridge clips.
FIGURE 1
FIGURE 2
SIDE TABLES AND HEADREST
Side Tables:
1. To place either table in raised position: raise table all the way up
and slide in until tabs engage slots in mount bracket. Press down
lightly on table to ensure lock tabs are engaged.
2. To return table to self-storing position: Lift table up until tabs
disengage from slots. Slide out and allow table to lower. (See
figure 5)
Articulating Headrest:
Articulating headrest may be adjusted to a comfortable position by
pulling forward or pushing back.
SEAT POSITIONING
Adjusting the recline:
Lock the rear casters. While holding the push
bar, squeeze the piston spring release handle.
To lower, push back on padded push handle.
To raise, pull forward on padded push handle.
To achieve the Shock Position, follow the
above steps and continue to lower the back
until the shock position pictured is achieved.
5. Raise the upholstered back to vertical position. Tuck the
plastic skirt at rear of upholstered back behind cross brace
of seat frame. Align the hinge at the bottom of the gas
spring with the holes in the "U" bracket in the seat frame
cross brace. While holding the back with one hand, secure
the gas spring hinge to the "U" bracket by replacing the
bolt with the other hand. Secure the bolt by replacing the
nut. (See figure 3)
Seat Frame:
1. Align holes in arm support mount to mounting holes in seat
frame. (See figure 4)
2. Insert screws through arm support mount and seat
frame holes. Secure screw with nut.
3. Repeat for other side.
FIGURE 3
Table (Disengaged Position)
Armrest
Clevis Pin
Table Mount
Bracket
Tabs engage into
slots on table
mount bracket
Table (Stored Position)
FIGURE 5
Recline Position 1
Recline Position 2
assembly..
Pedal protrudes
Push down
Every Three Months:
• Check and clean casters.
• Tighten nuts.
• Check brakes on casters.
• Check and clean lock recline mechanism.
For upholstery maintenance and stain removal,
FIGURE 4
the following hints will be helpful:
• Ordinary Dirt: Wash with warm water and a mild
soap or detergent.
• Stubborn Dirt: Using a soft bristle brush, follow
directions above.
Your Dynarex Geri Chair Recliner is warrantied to be
Table (Engaged Position)
free of defects in materials and workmanship for a
limited lifetime on the frame, and one (1) year on
upholstery and all moving parts, from original date of
purchase, for use by the original purchaser. This item
was built to exacting standards and carefully inspected
prior to shipment. This Warranty is an expression of our
confidence in the materials and workmanship of our
products and our assurance to the consumer of
dependable service.
The Warranty shall not apply under the following
conditions: problems arising from normal wear;
problems arising from failure to adhere to the product
instructions; problems arising from misuse, negligence,
accident or improper operation, maintenance or
storage; problems arising from modifications or
unauthorized repairs, parts or attachments; products
SYMBOL GLOSSARY
For an explanation of symbols
used in Dynarex packaging, visit
Shock Position
dynarex.com/symbols.php
CASTER OPERATIONS
TOTAL LOCK: Step on the rear pedal
of the caster until the pedal engages.
The front of pedal will protrude from
wheel cover.
UNLOCK: Step on the protruding front
part of the pedal to disengage lock to unlatch.
NOTE: This chair is equipped with four swivel
casters for improved maneuverability. The rear
casters are also equipped with locking features.
MAINTENANCE/CLEANING
• Ground-in Dirt: Scrub with powdered cleanser or
similar detergent.
• Chewing Gum: Scrape carefully.
• Nail Polish and Remover: Blot immediately to prevent
damage.
• Ball Point Pen: Blot immediately with a white cloth
dampened in water or mineral oil.
• Waxing and Refinishing: Improve wearability. Use any
quality paste wax.
NOTE: A diluted solution of 10% (or less) of bleach or
Clorox
may be used when cleaning this chair.
®
WARRANTY
where the serial number has been removed or defaced;
problems with non-durable components, such as
rubber accessories, casters, and grips, which are
subject to normal wear and need periodic replacement.
Dynarex shall not be liable for any consequential or
incidental damages whatsoever. Dynarex shall repair or
replace defective products at its option. The foregoing
warranty is exclusive and in lieu of other express
warranties, if any, including the implied warranties of
merchantability and fitness of a particular purpose. The
remedy for any violation of the implied warranty shall
be limited to repair or replacement of the defective
product pursuant to the terms contained herein.
If you have a question about your Dynarex device or
this warranty, please contact an authorized Dynarex
dealer.
Push down
R200701