- ページ 2

防犯カメラ HIKVISION DINOX DSR-3310のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。HIKVISION DINOX DSR-3310 2 ページ。

ページを印刷する

3. Attach the back box of type 1 camera /base plate

of type2 camera to the ceiling and secure them

with supplied self-tapping screws.

4.Route the cables through the cable hole.

5. Align the camera with the back box/base plate,

and tighten the set screws to secure the camera

with the back box/base plate.

Type I:

T T T y y y p p p e e e I I I I I I : : :

Figure 2-3 Fix the Camera to the Ceiling

6. Connect the corresponding cables.

7. Adjust the camera according to the figure below

to get an optimum angle.

8. Fit the black liner on the camera and tighten the

screws on the bubble of type 1 camera or rotate the

bubble of type 2 camera to complete.

Type I:

Type II:

0°~90°

T Direction

0°~90°

T Direction

0°~355°

R Direction

P Direction

R Direction

0°~355°

Figure 2-4 Zoom and Focus Adjustment

2.2 In-ceiling Mounting

You need to purchase an in-ceiling mount separately

if you adopt in-celling mounting.

Steps:

1. Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2. Screw the bolts through the mount by aligning

with the 2 bolt holes. Fit the toggles onto the bolts.

3.Push the two toggle bolts through the two screw

holes on the ceiling. Rotate the bolt till the toggle

holds the ceiling tightly.

Figure 2-5 Install the Mount

4. Route and connect the corresponding cables.

5. Fix the camera to the in-ceiling mount with the

supplied screws.

Type II:

Type I:

Figure 2-6 Fix the Camera to the Mount

6. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

2.3 In-ceiling Mounting with

Gang Box

Only the type 1 camera supports in-ceiling

mounting with gang box.

1. Repeat steps 2-3 of the In-ceiling Mounting

section to secure the in-ceiling mount (supplied)

to the gang box.

Figure 2-7 Install the Mount

2. Route and connect the corresponding cables.

3.Align the camera with the gang box, and tighten

the screws to secure the camera with the gang box..

0°~340°

P Direction

Figure 2-8 Fix the Camera to the Gang Box

4. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

3 Menu Operation

VIDEO.

SETUP

OUT

SCENE

LENS

EXPOSURE

BACKLIGHT

DAY&NIGHT

INDOOR

MANUAL

SHUTTER

BLC

ATW

COLOR

OUTDOOR

AGC

HSBLC

AWC-SET

B/W

INDOOR1

SENS-UP

MANUAL

EXT

LOW-

BRIGHTNESS

LIGHT

D-WDR

DEFOG

Figure 3-1 Main Menu

You can call the menu and adjust the camera

parameters with a coaxial camera controller

(purchase separately). You can also call the menu

with supported TVI DVR.

3.1 VIDEO.OUT

PAL or NTSC is selectable .

3.2 LANGUAGE

English, Japanese, CHN1, CHN2, Korean, German,

French, Italian, Spanish, Polish, etc., are selectable.

3.3SETUP

3.3.1 SCENE

You can select indoor, outdoor, indoor 1 and low

-light as the working environments.

3.3.2 LENS

The camera is equipped with a fixed lens.

3.3.3 EXPOSURE

SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,

1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,

and x15 are selectable.

AGC: You can set the AGC value from 0 to 15.

SENS-UP: You can set the SENS-UP to OFF or AUTO.

BRIGHTNESS: You can set the brightness value

from 1 to 100.

DEFOG: You can set the defog function as ON to

enable the function. Position, size, and the defog

gradation are configurable.

D-WDR: You can set the D-WDR as ON or OFF.

EXPOSURE

1. SHUTTER

2. AGC

3. SENS-UP

4. BRIGHTNESS

---|------ 40

5. DEFOG

6. D-WDR

7. RETURN

Figure 3-2 Exposure

3.3.4 Backlight

Backlight Compensation (BLC):

-GAIN: Set the gain of BLC as High, Middle, or Low.

-AREA: Press the up/down/left/right button to

define the BLC position and size. Select RET or

AGAIN to go back the BLC menu or re-define the

BLC area.

-Default: Restore the BLC settings to the default.

HSBLC: Select an HSBLC area. Set the DISPLAY

status as ON. Press the up/down/left/right button

to define the area position and size. Set the HSBLC

LEVEL from 0 to 100. Select ALL DAY or Night for the

LAUGUAGE

HSBLC mode. Set the BLACK MASK status as ON or

SPECIAL

ADJUST

RESET

OFF.

CAM

2D NR

EXIT

SHARPNESS

TITLE

3.3.5 White Balance (WB)

3D NR

D-EFFECT

MONITOR

MANUAL, ATW (Auto-tracking White Balance),

MOTION

LSC

AWC→SET are selectable.

PRIVACY

3.3.6 Day & Night

DEFECT

Color, B/W, and EXT are selectable for DAY and

VERSION

NIGHT switches.

3.3.7 NR

2D NR: You can set 2D NR status as ON or OFF.

3D NR: Set the Smart NR status as ON and adjust

the 3D smart NR sensitivity ranges from 0 to 100.

Set the 3D NR LEVEL ranges from 0 to 100. Set the

START. AGC level as the threshold to enable AGC,

and set the END. AGC level as the threshold to

disable AGC.

HSBLC

AUTO

1. SELECT

AREA 1

OFF

2. DISPLAY

ON 8

---

3. LEVEL

---|------ 40

4. MODE

ALL DAY

Motion: Select a MOTION area. Set the DISPLAY

5. BLACK MASK

OFF

6. DEFAULT

status as ON or OFF. Press the up/down/left/right

OFF

7. RETURN

RET

button to define the position and size of the area.

RET

Set the SENSITIVITY from 0 to 60. Set the MOTION

Figure 3-3 HSBLC

Privacy: Select a PRIVACY area. Set the DISPLAY

status as INV, MOSAIC, COLOR or OFF. Press the

up/down/left/right button to define the position

and size of the area.

3.3.9 ADJUST

Sharpness: Adjust the sharpness from 0 to 15.

Monitor: Monitor CRT, and Monitor LCD are

selectable.

LSC: Set the LSC status as ON or OFF.

3.3.10 RESET

Reset all the settings to the default.

3.3.11 EXIT

Press OK to exit the menu.

3D NR

1. SMART NR

2D&3D NR

2. LEVEL

------|--8 0

3. START. AGC -|--------10

1. 2DNR

OFF

4. END. AGC

-|--------10

2. 3DNR

5. RETURN

RET

3. RETURN RET

Figure 3-5 3D NR

Figure 3-4 NR

3.3.8 SPECIAL

Camera Title: Edit the camera title on this section.

D-effect:

-FREEZE: Set the freeze function as ON or OFF.

-MIRROR: OFF, MIRROR, V-FLIP, and ROTATE are

selectable for mirror.

-D-ZOOM: Define the zoom area by configuring

the position from PAN & TILT.

-SMART D-ZOOM: The D-Zoom area, sensitivity

and time are configurable.

-NEG.IMAGE: Set the NEG IMAGE as ON or OFF.

MOTION

SPECIAL

1. CAM TITLE

1. SELECT

AREA 1

2. D-DFFECT

2. DISPLAY

ON8

3. MOTION

OFF

3. SENSITIVITY

----|---- 30

4. PRIVACY

OFF

4. MOTION VIEW ON

5. LANGUAGE

ENG

5. DEFAULT

6. DEFECT

6. RETURN

RET

7. RETURN

RET

Figure 3-7 Motion Detection

Figure 3-6 Special

VIEW status as ON or OFF.

Defect: LIVE DPC, STATIC DPC and Black DPC are

adjustable in this section.

PRIVACY

ADJUST

1. SELECT

AREA 1

--------|15

1. SHARPNESS

2. DISPLAY

MOSAIC

3. COLOR

2. MONITOR

LCD8

4. TRANS.

3. LSC

OFF

4. RETURN

RET

5. DEFAULT

6. RETURN

RET

Figure 3-8 Privacy Mask

Figure 3-9 Adjust