HIKVISION DINOX DSR-3310 Kullanıcı Kılavuzu - Sayfa 2

Güvenlik Kamerası HIKVISION DINOX DSR-3310 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. HIKVISION DINOX DSR-3310 2 sayfaları.

Sayfayı Yazdır
HIKVISION DINOX DSR-3310 Kullanıcı Kılavuzu
3. Attach the back box of type 1 camera /base plate
of type2 camera to the ceiling and secure them
with supplied self-tapping screws.
4.Route the cables through the cable hole.
5. Align the camera with the back box/base plate,
and tighten the set screws to secure the camera
with the back box/base plate.
Type I:
T T T y y y p p p e e e I I I I I I : : :
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adjust the camera according to the figure below
to get an optimum angle.
8. Fit the black liner on the camera and tighten the
screws on the bubble of type 1 camera or rotate the
bubble of type 2 camera to complete.
Type I:
Type II:
0°~90°
T Direction
0°~90°
T Direction
0°~355°
R Direction
P Direction
R Direction
0°~355°
Figure 2-4 Zoom and Focus Adjustment
2.2 In-ceiling Mounting
You need to purchase an in-ceiling mount separately
if you adopt in-celling mounting.
Steps:
1. Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2. Screw the bolts through the mount by aligning
with the 2 bolt holes. Fit the toggles onto the bolts.
3.Push the two toggle bolts through the two screw
holes on the ceiling. Rotate the bolt till the toggle
holds the ceiling tightly.
Figure 2-5 Install the Mount
4. Route and connect the corresponding cables.
5. Fix the camera to the in-ceiling mount with the
supplied screws.
Type II:
Type I:
Figure 2-6 Fix the Camera to the Mount
6. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
2.3 In-ceiling Mounting with
Gang Box
Only the type 1 camera supports in-ceiling
mounting with gang box.
1. Repeat steps 2-3 of the In-ceiling Mounting
section to secure the in-ceiling mount (supplied)
to the gang box.
Figure 2-7 Install the Mount
2. Route and connect the corresponding cables.
3.Align the camera with the gang box, and tighten
the screws to secure the camera with the gang box..
0°~340°
P Direction
Figure 2-8 Fix the Camera to the Gang Box
4. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
3 Menu Operation
Menu
VIDEO.
SETUP
OUT
SCENE
LENS
EXPOSURE
BACKLIGHT
WB
DAY&NIGHT
INDOOR
MANUAL
SHUTTER
BLC
ATW
COLOR
OUTDOOR
AGC
HSBLC
AWC-SET
B/W
INDOOR1
SENS-UP
MANUAL
EXT
LOW-
BRIGHTNESS
LIGHT
D-WDR
DEFOG
Figure 3-1 Main Menu
You can call the menu and adjust the camera
parameters with a coaxial camera controller
(purchase separately). You can also call the menu
with supported TVI DVR.
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the working environments.
3.3.2 LENS
The camera is equipped with a fixed lens.
3.3.3 EXPOSURE
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,
and x15 are selectable.
AGC: You can set the AGC value from 0 to 15.
SENS-UP: You can set the SENS-UP to OFF or AUTO.
BRIGHTNESS: You can set the brightness value
from 1 to 100.
DEFOG: You can set the defog function as ON to
enable the function. Position, size, and the defog
gradation are configurable.
D-WDR: You can set the D-WDR as ON or OFF.
EXPOSURE
1. SHUTTER
2. AGC
3. SENS-UP
4. BRIGHTNESS
---|------ 40
5. DEFOG
6. D-WDR
7. RETURN
Figure 3-2 Exposure
3.3.4 Backlight
Backlight Compensation (BLC):
-GAIN: Set the gain of BLC as High, Middle, or Low.
-AREA: Press the up/down/left/right button to
define the BLC position and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
-Default: Restore the BLC settings to the default.
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
to define the area position and size. Set the HSBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
LAUGUAGE
HSBLC mode. Set the BLACK MASK status as ON or
SPECIAL
ADJUST
RESET
NR
OFF.
CAM
2D NR
EXIT
SHARPNESS
TITLE
3.3.5 White Balance (WB)
3D NR
D-EFFECT
MONITOR
MANUAL, ATW (Auto-tracking White Balance),
MOTION
LSC
AWC→SET are selectable.
PRIVACY
3.3.6 Day & Night
DEFECT
Color, B/W, and EXT are selectable for DAY and
VERSION
NIGHT switches.
3.3.7 NR
2D NR: You can set 2D NR status as ON or OFF.
3D NR: Set the Smart NR status as ON and adjust
the 3D smart NR sensitivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
HSBLC
AUTO
1. SELECT
AREA 1
OFF
2. DISPLAY
ON 8
---
3. LEVEL
---|------ 40
4. MODE
ALL DAY
Motion: Select a MOTION area. Set the DISPLAY
5. BLACK MASK
ON
OFF
6. DEFAULT
status as ON or OFF. Press the up/down/left/right
8
OFF
7. RETURN
RET
button to define the position and size of the area.
RET
Set the SENSITIVITY from 0 to 60. Set the MOTION
Figure 3-3 HSBLC
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size of the area.
3.3.9 ADJUST
Sharpness: Adjust the sharpness from 0 to 15.
Monitor: Monitor CRT, and Monitor LCD are
selectable.
LSC: Set the LSC status as ON or OFF.
3.3.10 RESET
Reset all the settings to the default.
3.3.11 EXIT
Press OK to exit the menu.
3D NR
1. SMART NR
ON
8
2D&3D NR
2. LEVEL
------|--8 0
3. START. AGC -|--------10
1. 2DNR
OFF
4. END. AGC
-|--------10
2. 3DNR
ON
8
5. RETURN
RET
3. RETURN RET
Figure 3-5 3D NR
Figure 3-4 NR
3.3.8 SPECIAL
Camera Title: Edit the camera title on this section.
D-effect:
-FREEZE: Set the freeze function as ON or OFF.
-MIRROR: OFF, MIRROR, V-FLIP, and ROTATE are
selectable for mirror.
-D-ZOOM: Define the zoom area by configuring
the position from PAN & TILT.
-SMART D-ZOOM: The D-Zoom area, sensitivity
and time are configurable.
-NEG.IMAGE: Set the NEG IMAGE as ON or OFF.
MOTION
SPECIAL
1. CAM TITLE
ON
8
1. SELECT
AREA 1
2. D-DFFECT
8
2. DISPLAY
ON8
3. MOTION
OFF
3. SENSITIVITY
----|---- 30
4. PRIVACY
OFF
4. MOTION VIEW ON
5. LANGUAGE
ENG
8
5. DEFAULT
8
6. DEFECT
8
6. RETURN
RET
7. RETURN
RET
Figure 3-7 Motion Detection
Figure 3-6 Special
VIEW status as ON or OFF.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this section.
PRIVACY
ADJUST
1. SELECT
AREA 1
--------|15
8
1. SHARPNESS
2. DISPLAY
MOSAIC
3. COLOR
10
2. MONITOR
LCD8
4. TRANS.
1
3. LSC
OFF
8
4. RETURN
RET
5. DEFAULT
6. RETURN
RET
Figure 3-8 Privacy Mask
Figure 3-9 Adjust