- ページ 6

おもちゃ Green R/C Model Airplanes Tiger MothのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Green R/C Model Airplanes Tiger Moth 11 ページ。 The unique almost-ready-to-fly scale 1:7 model of great britain's famous wwii training aircraft
Green R/C Model Airplanes Tiger Moth にも：取扱説明書 (11 ページ)

ページを印刷する

Green R/C Model Airplanes Tiger Moth 取扱説明書

Step

Step 3. 3. 3. 3. Mount

Mount

the

main

Step

Mount

Mount the

the main

the

main

main landing

* * * * Open

Bag

Bag 9# 9# 9# 9# and

hardware needed. . . .

1) Turn the fuselage up side down again. The wires of the main landing gear assembly may need

spreading to match the fore and the rear slots that are located under the covering.

2) There are holes pre-drilled in the bottom of the fuselage for mounting the main landing gear. You

don't need to cut away the covering in the slots. The gear wire will push the covering into the

slots when you tighten the mounting screws . Leaving the covering in the slots will help keep the

wood from getting oil soaked.

3) Slip the main wheels on the axles and use the four wheel collars (L03) to retain the wheels in

place.

4) Finally, fix the main landing gear assembly in place by tightening the mounting screws (L05) in

the hold-down plates (L04) as shown in Fig. (3).

4. Tail gear

Step

Step 4. 4. 4. 4. Mounting

Mounting

the

Step

Mounting the

Mounting

the

the tail

Bag.11#

*Open Bag.11#

Bag.11# to get the tail

*Open

to get the fin

Bag

Bag 12#

12#

*Open

Bag

13#

to get the rudder

Bag

Bag 13#

13#

1) Mount the control horns onto the rudder and elevator respectively.

2) Place the tail wheel on the tail gear axle and use one of the wheel collars (L08) to retain it in

place. The other collar is used to prevent the gear from moving upward through the hole in the

tail gear mounting plate (L09)

3) Insert the sharp end of the tail-gear strut into the hole pre-drilled in the fin and apply thin CA to

secure it in the fin.

4) Refer to Fig. (4), mount the tail surfaces along with the tail wheel sub-assembly onto the tail end

of the fuselage by inserting the two long tail-surfaces mounting bolts (T03) into the holes &

tubes pre-built in the fuselage and securely tightening the bolts into the nuts

Thus, the complete tail-surfaces are fixed in place.

All manuals and user guides at all-guides.com

landing

gear

sub-assembly

landing

landing gear

gear sub-assembly

gear

sub-assembly

main

to get the main

main landin

and

and 10#

10#

Fig.

(4)

Assembly

Assembly of of of of the

Fig.

Fig. (4)

(4) Assembly

1. Elevator

7. Tail gear mounting screws

tail

surfaces

and

the

tail

tail surfaces

surfaces

surfaces and

and the

and

the tail

the

tail

wheel

tail wheel

wheel (L06), tail

fin

hinged

with

rudder

fin hinged

hinged with

with rudder

rudder

control

horns

rudder control

control horns

horns (C01) and elevator

landin

gear

assembly

assembly (L01) , , , , main

assembly

landin gear

gear assembly

the

tail-surfaces

and

the

the tail-surfaces

tail-surfaces and

and the

the tail

2. Rudder

5. Tail wheel

8. Tail-surfaces mounting bolt

tail

wheel

tail

tail wheel

wheel

tail

gear

tail gear

gear (L07), and other hardware needed

stabilizer

rudder (T01) and the stabilizer

stabilizer hinged

elevator

elevator control

main

wheels

main wheels

wheels (L02) and other

tail

wheel

tail wheel

wheel

3. Retaining collar

6. Mounting plate

hinged

with

elevator

elevator (T02) . . . .

hinged with

with elevator

control

horns

control horns

horns (C04).

nuts

nuts built into the fin.

nuts