- ページ 2

IPカメラ ALIBI ALI-CD5021VSSのPDF クイックインストールとユーザーマニュアルをオンラインで閲覧またはダウンロードできます。ALIBI ALI-CD5021VSS 4 ページ。 Hd-tvi extreme outdoor ir dome camera

ページを印刷する

During installation:

Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens or dome. If the

•

lens or IR array shield becomes soiled, clean it only with approved products. See the

Monitor impedance: If you use a setup monitor when installing the camera, ensure that the

•

monitor input impedance is set to 75 Ω.

Power supply: Camera drop cable: The camera drop cable includes two connectors:

•

Video BNC connector: For transmission of the HD-TVI video signal across a coax (75 Ω)

—

extension cable. This cable must connect to an HD-TVI compatible video player or recorder

Power connector: When applying Vdc power, observe the power polarity. See the picture to the

—

picture of the drop cable connectors on page 1.

The following procedure outlines an installation of the camera to a mounting surface. Your installation

steps may differ, depending on how the camera is mounted and how the drop cable connects to video and

power extension cables. To install the camera onto a surface:

Separate the camera dome cover assembly from the camera module by loosening the two hex

screws on the sides of the dome using the L-wrench provided. Note that the dome cover is tethered

to the camera module.

Using the drill template or the base housing, mark the locations of the mounting screw holes, and

the hole for the drop cable if routing the cable through the mounting surface.

Hole for

mounting

screw

Inside view of mounting base

Apply a small but adequate amount of silicone sealant around the holes for the mounting screws in

the mounting base.

Using appropriate fasteners, secure the mounting base to the mounting surface. The mounting

screws and wall inserts are adequate for many surface types.

Route power and video extension cables from your 12 Vdc power source and monitoring equipment

to the mounting location. Do not apply power to the power extension cable at this time.

Connect the camera drop cables to the video and power extension cables. NOTE: Camera drop

cable connectors are not waterproof. Use appropriate seals to protect these connections from

contamination.

NOTE

The HD-TVI video cable must attach to the HD-TVI compatible equipment.

Apply power to the camera. Use caution to observe the DC power polarity shown in the drop cable

photo on page 1.

Verify that a video signal can be seen on your video monitoring equipment.

Step 2.

Adjust the camera for your surveillance target

Observe the live video on your monitoring equipment, or plug a video setup monitor (not provided)

into the RCA jack inside the camera.

www.observint.com

To adjust the camera pan, grasp the camera gimbal on both sides at the pivot point, then rotate the

as shown in the illustration below to point it at your surveillance target.

section.

Cleaning

To adjust the tilt, loosen the two tilt adjust set screws (one on each side), and then rock the gimbal

as shown above in the right illustration.

To adjust the camera horizon line, grasp the camera head carefully and rotate it as shown in the

photo below.

Holes for

mounting

screws

Unscrew the Wide - Tele and Near - Far adjustment levers about 1/4 turn, then adjust the lens zoom

and focus as needed. Tighten the levers screws until snug to hold them in place.

Dome gasket

Wide (W) /Tele (t)

zoom control

If you choose to configure the camera OSD settings remotely (through the HD-TVI HVR), apply a thin

bead of silicone sealant around the rubber dome gasket, and then reinstall the camera dome cover

assembly. Ensure that the inside of the dome is clean.

Otherwise, continue with "Step 3. Setup the camera using the OSD" on page 2.

Step 3.

Setup the camera using the OSD

Use the OSD to customized the internal settings of the camera for the installation environment.

Remove the camera dome cover assembly if it is installed.

Find the OSD joystick. It is located on the circuit board behind the camera module.

adjust set

screw (2)

Pan adjustment

Horizon line adjustment

Tilt

Tilt adjustment

Near (N) / Far (F)

focus control