- ページ 3

IPカメラ ALIBI ALI-NS4018RのPDF クイック・インストール・マニュアルをオンラインで閲覧またはダウンロードできます。ALIBI ALI-NS4018R 4 ページ。 Ip bullet cameras

ページを印刷する

Click on the message to install the plugin.

NOTE: If QuickTime is installed on the computer, Alibi will use it for the plugin. If it

does, skip the rest of this step and continue at the next

In the message bar at the bottom of the screen, click Run. WebComponents will install

automatically. When the following screen opens, click Finish to exit the installer.

The Live View screen with the camera video image should appear.

Screen select tabs

Step 3.

Adjust the camera for your surveillance target

While observing live video from your camera in the Live View tab (see above), loosen the lock

nut, and then point at the center of your surveillance target. Tighten the lock nut to hold the

camera in place.

www.observint.com

Live View image

Logout button

Capture, Record, Zoom icons

Pan:

0˚ ~ 360˚

Tilt:

Rotation:

0˚ ~ 90˚

0˚ ~ 360˚

After adjusting the camera for the preferred field of view, click the Setup tab, and then click the

Image link in the left frame.

Adjust the Brightnessm Contrast, Saturation and Sharpness of the image as follows.

Image Adjustment submenu (see above): Adjust the Saturation, Hue, Brightness,

—

Contrast and Sharpness of the video image. Each parameter can be set to a level of

0 ~ 100 either by moving the slider or entering the value in the box on the right. The

effect of the adjustment will appear in the Live View image in the menu.

Open the other submenus on this screen. Adjust the following as needed. Refer to the Camera

Firmware User Manual for your camera for additional information about parameter settings.

Exposure Settings submenu: In this submenu, set the following for the best

—

performance:

Iris Mode: Select Auto or Manual. Some cameras may not offer both options.

Exposure Time: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150.

Adjust it according to the lightening condition.

Gain: Set the gain to show the optimal brightness level.

Switch Day and Night: Select either Auto-Switch, Scheduled-Switch, or

—

Triggered by Alarm Input.

If using Auto-Switch, open the Day/Night Switch submenu to select the

Sensitivity, Filtering Time, and Smart IR feature ON or OFF.

If using Scheduled Switch, set the Start Time and End Time of the switch, then

open the Day/Night Switch submenu to select the Smart IR feature ON or OFF.

Also, click the Common, Day and Night tabs to set the Saturation, Hue, Brightness,

Contrast and Sharpness for Day and for Night modes.

Day/Night Switch submenu: You can set the Day/Night switch to Day, Night, Auto, or

—

Schedule. The option you select determines the submenu options.

Day or Night: These options both have one parameter: Smart IR.

Auto: If you select Auto switch, you can set the sensitivity (0 .. 7), filtering time and

Smart IR.

Schedule: Use Schedule to set that Start Time and End Time for the switch. Smart

IR is also selectable.

Backlight Settings: Backlight settings include BLC Area (Off, Up, Down Left Right

—

Center), the area to control, and WDR (Wide Dynamic Range) ON or OFF.

White Balance: White Balance selection is used to correct colors in the image

—

depending on the lighting source. You can also set the white balance manually (MWB),

using Automatic White Balance (AWB1), and lock the white balance setting (Locked WB).

Image Enhancement: Options in this submenu include Digital Noise Reduction (DNR)

—

ON or OFF. If ON, you can also adjust the level of noise reduction.

Video Adjustment: Video Adjustment includes:

—

Lock nut