- ページ 4

スピーカー Avantone Pro Active MixCubeのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Avantone Pro Active MixCube 8 ページ。 Powered mini-reference monitors

ページを印刷する

(3)

CONNECTING your MixCubes

Before plugging in and powering up your MixCubes please take a moment to be certain that

the proper AC MAINS operating voltage setting has been selected on the transformer/power

supply.

Set all faders and level controls to minimum on your console/monitors feed. All other

equipment should be powered up before turning on the MixCubes so as to avoid loud turn-

on spikes and surges. The input "SYSTEM GAIN" control is set at minimum at the factory so

as to avoid an accidental overload upon initial hookup. This is intended to force the

engineer to purposefully set the gain where appropriate and safe in reference to the monitor

send output level from the console.

SPECIFICATIONS

SYSTEM TYPE: Active (Self-Powered) shielded full-range stereo pair

SYSTEM FREQUENCY RESPONSE: 90Hz-17,000Hz (Accessible musical range)

MAX SPL: 104dB 1 meter @1%THD (PINK NOISE)

AMPLIFIER: Class A/B

AMP POWER: 60 watts RMS@ .005% THD (1KHz)

AMP FREQ. RESPONSE: 22Hz-50KHz +0dB/- 3dB (90Hz-50KHz +/-0dB)

NOISE: S/N -113 dB "A" Weighted

COOLING: Convection / Heat Sink-Aluminum Fins

DRIVER: Proprietary Design-8 ohm 5.25" Cast Aluminum Frame / Paper Cone/Shielded

CABINET: Sealed design /18mm MDF/ with Dacron Acoustical stuffing

INPUTS: XLR & TRS +4/Balanced and -10 unbalanced

SENSITIVITY: 0dBu (.775VRMS) input at maximum volume (+6dB) = 104dB SPL

CABINET DIMENSIONS: 165mm x 165mm x 165mm ( 6 ½"x 6 ½"x 6 ½" )

CABINET WEIGHT: 3.55kgs / 7.8 Lbs (each)

WARRANTY: 5 Year Limited Warranty to original purchaser

Break-In

MixCubes "

" suggestions:

Because any new full range speaker exhibits a certain amount of "tightness" when first played, you

will most likely benefit from a "break-in" of the MixCubes if you are going to be doing critical work

almost immediately. Normally, standard usage of the speakers over a short period of time is all that

is required before you recognize the tonal changes taking place with the driver "flexing" from some

hours of use. However, if you need to "get to work" immediately; then we do have a suggested

"break-in" mode that will advance the "natural time process" much quicker. Here is the "quick

version"!

Though the MixCubes do perform solidly right out of the box it is beneficial to actually run them

through a "burn-in" period before using them in professional mix situations.

Some High-end speaker manufacturers claim that many speakers need a 100-200 hour break-in

period before they are "normalized" which most professional engineers do just to get use to their

new monitors.

We feel that simply playing any commercial music CD with good low frequency content through

them on a loop for 24-72 hours at a medium volume level can easily do this.

This procedure serves to "normalize" the driver surrounds by flexing them.

Users have reported that this sped up the break-in process and the MixCubes seemed to "open-up"

a bit more than when first powered up.

Whatever process you utilize, rest assured that you have purchased an amazing tool that will aid in

determining the proper levels and tones of your all-important mixes!

This "Break-In" suggestion is being recommended to remind you that like all things new, (i.e. a new

sports car), a short break-in time is a good time for the driver to flex and normalize. Enjoy and

here's to accurate mixes!