- ページ 5

レンジ KitchenAid YKESA907PS00のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid YKESA907PS00 20 ページ。 30"(76.2cm) freestanding and slide-in electric ranges

ページを印刷する
Ifcodes permit and a separate ground w ire isused, i tis
recommended
thata qualified electrical installer determine that
theground p athand wire gauge areinaccordance withlocal
codes.
Ifcodes permit and a separate ground w ire isused, i tis
recommended
thataqualified electrician determine thatthe
ground p athisadequate.
Donotuseanextension cord.
Besure that t heelectrical connection andwire size areadequate
andinconformance
withtheNational Electrical Code, ANSI/
NFPA 7 0-latest edition and alllocal c odes a ndordinances.
Acopyoftheabove c ode standards canbeobtained from:
National Fire Protection Association,
One Batterymarch
Park,
Quincy, MA 02269.
Electrical
Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
•
Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating
plate. (The model/serial number rating plate is located on the
oven frame behind the storage drawer panel.)
When a 4-wire or 3-wire, single phase 120/240-volt,
60 Hz,
AC-only electrical supply is available, a 50 amp maximum
circuit protection is required (or, if specified on the model/
serial rating plate, when a 4-wire or 3-wire single phase
120/208-volt
60 Hz, AC-only electrical supply is available, a
40 amp maximum circuit protection is required), fused on
both sides of the line.
•
A time-delay fuse or circuit breaker is recommended.
The range can be connected directly to the fused disconnect
(or circuit breaker box) through flexible, armored or
nonmetallic
sheathed, copper or aluminum cable. See
"Electrical Connection."
•
Allow 2 to 3 ft of slack in the line so that the range can be
moved if servicing is ever necessary.
•
A UL listed conduit connector must be provided at each end of
the power supply cable (at the range and at the junction box).
•
Wire sizes and connections must conform with the rating of
the range (40 amps).
•
The wiring diagram is located on the underside of the storage
drawer or below the warming drawer in a clear plastic bag.
If connecting
to a 4-wire system:
This range is manufactured
with the ground connected to the
cabinet. The ground must be revised so the green grounding wire
of the 4-wire power supply cord is connected to the cabinet. See
"Electrical Connection."
Grounding through the neutral conductor
is prohibited for new
branch-circuit
installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40 amp, range power supply
cord (pigtail) must be used. This cord contains 4 copper
conductors
with ring terminals or open-end spade terminals with
upturned ends, terminating
in a NEMA Type 14-50P plug on the
supply end.
The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
and be at least 4 ft (1.22 m) long.
4-wire receptacle (14-50R)
The minimum conductor sizes for the copper 4-wire power
cord are:
40 amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-8 green grounding
If connecting
to a 3-wire system:
Local codes may permit the use of a UL listed, 3-wire,
250-volt, 40 amp range power supply cord (pigtail). This cord
contains 3 copper conductors
with ring terminals or open-end
spade terminals with upturned ends, terminating
in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.
3-wire receptacle (10-50R)
Electrical
Shock Hazard
Emectricaliy ground
range.
Failure to follow these instructions
can resumt in death,
fire, or electdcam shock.
If codes permit and a separate ground wire is used, it is
recommended
that a qualified electrical installer determine that
the ground path and wire gauge are in accordance
with local
codes.